ABB 615 Series ANSI Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 60

background image

1MAC052634-MB D

Section 3

Vendor-specific implementation

615/620 series ANSI

35

Communication Protocol Manual

Table 25:

Interpretation of the integer status data value

Table 26:

Interpretation of the ACD data

Table 27:

Interpretation of the SEC data

The original SEC cnt attribute is actually defined as a 32 bit counter. The Modbus event
shows the least significant 16 bits of that counter (i.e., 0 - 65535).

3.3.8.4

Multiple event records reading

It is possible to read out up to 10 sequential event records in one event select/read
transaction. The number of sequential event records to be returned for reading shall be
written to the Num of records register in front of the selection register. This number can
be written once or it can be rewritten for each select/read transaction. If this number is
never written, only one event record is returned.

If the Modbus client requests multiple event records, the returned records should also be
read out by the client. One record consists of 11 registers, two records of 22 registers and
so on. The read length must thus be adjusted depending on the number of records
requested.

The selection/read operation is otherwise exactly similar to the single-record read case.
The next records to be returned always continues from the last record in the previous read
operation.

Register address

1

1. See Modbus ANSI point list manual for specific event record structure mappings.

Meaning

4xxxx

Higher 16 bit part of the 32 bit integer value

4xxxx + 1

Lower 16 bit part of the 32 bit integer value

Register address

1

1. See Modbus ANSI point list manual for specific event record structure mappings.

Meaning

4xxxx

xxxx.xxxx.xxxx.xxx0 Object in OFF position
xxxx.xxxx.xxxx.xxx1 Object in ON position

4xxxx + 1

xxxx.xxxx.xxxx.xx00 Start in unknown direction
xxxx.xxxx.xxxx.xx01 Start in forward direction
xxxx.xxxx.xxxx.xx10 Start in backwards direction
xxxx.xxxx.xxxx.xx11 Start in both directions

Register address

1

1. See Modbus ANSI point list manual for specific event record structure mappings.

Meaning

4xxxx

xxxx.xxxx.xxxx.x000 Unknown security violation
xxxx.xxxx.xxxx.x001 Critical security violation
xxxx.xxxx.xxxx.x010 Major security violation
xxxx.xxxx.xxxx.x011 Minor security violation
xxxx.xxxx.xxxx.x100 Warning

4xxxx + 1

Security violations counter, 16 bits

«
...
39
40
41
42
43
...
»

Содержание 615 Series ANSI





























































Отзывы:

Нет отзывов

Похожие инструкции для 615 Series ANSI

Бренд: jablotron Страницы: 2

Бренд: Magnescale Страницы: 3

nERGY bluePRINT ENGCP15001

Бренд: Soundoff Signal Страницы: 5

Бренд: HomeMatic Страницы: 36

Бренд: Kohler Страницы: 48

AUTOPULSE IQ-318

Бренд: Notifier Страницы: 62

Бренд: SMC Networks Страницы: 15

Infi 90 IMSPM01

Бренд: Bailey Страницы: 52

Бренд: SMC Networks Страницы: 31

Бренд: Znshine Solar Страницы: 16

Phase Matrix PXI-1420

Бренд: National Instruments Страницы: 38

Бренд: WAGO Страницы: 134

Бренд: GAC Страницы: 9

Бренд: ALLEN & HEATH Страницы: 15

Бренд: GIESSE Страницы: 136

BALBOA CS6000B Series

Бренд: HydroQuip Страницы: 32

EXTA LIFE P-520

Бренд: Zamel Страницы: 10

Бренд: Lennox Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды