background image

 

 

2TLC172178M0201, rev. D 

www.abb.com/lowvoltage 

2011-11-15  

Read and understand this document 

Please read and understand this document before using the products. Please consult your ABB/JOKAB SAFETY 
representative if you have any questions or comments. 

WARRANTY 

ABB/JOKAB SAFETY’s exclusive warranty is that the products are free from defects in materials and workmanship 
for a period of one year (or other period if specified) from date of sale by ABB/JOKAB SAFETY.  

ABB/JOKAB SAFETY MAKES NO WARRANTY OR REPRESENTATION, EXPRESSED OR IMPLIED, 
REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF 
THE PRODUCTS, ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS 
DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OR THEIR INTENDED 
USE. ABB/JOKAB SAFETY DISCLAIMS ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED. 

LIMITATIONS OF LIABILITY 

ABB/JOKAB SAFETY SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL 
DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, 
WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY.  

In no event shall responsibility of ABB/JOKAB SAFETY for any act exceed the individual price of the product on 
which liability asserted.  

IN NO EVENT SHALL ABB/JOKAB SAFETY BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER 
CLAIMS REGARDING THE PRODUCTS UNLESS ABB/JOKAB SAFETY’S ANALYSIS CONFIRMS THAT THE 
PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO 
ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. 

SUITABILITY FOR USE 

ABB/JOKAB SAFETY shall not be responsible for conformity with any standards, codes, or regulations that apply 
to the combination of products in the customer’s application or use of the product. At the customer’s request, 
ABB/JOKAB SAFETY will provide applicable third party certification documents identifying ratings and limitations of 
use that apply to the products. This information by itself is not sufficient for a complete determination of the 
suitability of the products in combination with the end product, machine, system, or other application or use.  

The following are some examples of applications for which particular attention must be given. This is not intended 
to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be 
suitable for the products:  

Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not 
described in this document.  

Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, 
amusement machines, vehicles, and installations subject to separate industry or government regulations.  

Systems, machines, and equipment that could present a risk to life or property.  

Please know and observe all prohibitions of use applicable to the products.  

NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY 
WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, 
AND THAT THE ABB/JOKAB SAFETY PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE 
INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. 

PERFORMANCE DATA 

While every effort has been taken to ensure the accuracy of the information contained in this manual ABB/JOKAB 
SAFETY cannot accept responsibility for errors or omissions and reserves the right to make changes and 
improvements without notice. Performance data given in this document is provided as a guide for the user in 
determining suitability and does not constitute a warranty. It may represent the result of ABB/JOKAB SAFETY’S 
test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to 
the ABB/JOKAB SAFETY Warranty and Limitations of Liability. 

Содержание 2TLA020009R0500





















Отзывы: