background image

5

1.2

Type marking

The type marking of the modem consists of a type number, a temperature range code and
a country code. The type number is 1MRS119000-_ _ _. The one-letter temperature range
code and the two-letter country code specify the service temperature range and the desti-
nation country where the modem is to be installed. The country code is needed to make
sure that the public line part of the modem has been approved for use in the destination
country. The status of approval per country can be inquired from ABB Transmit Oy or
ABB's local customer centre.

Example of the type marking:

1MRS119000 -AFI
|

|    |

|

| Country code

FI = Finland

|

|

|

Temperature range A = +5…+50

°

C

|

B = -20…+60

°

C

Type number

Country codes are:
AR = Argentina

AT = Austria

AU = Australia

BE = Belgium

BR = Brazil

CA = Canada

CH = Switzerland

CO = Colombia

CZ = Czech republic

DE = Germany

DK = Denmark

EE = Estonia

EG = Egypt

ES = Spain

FI = Finland

GB = Great Britain

GR = Greece

HK = Hong Kong

HU = Hungary

ID = Indonesia

IE = Ireland

IL = Israel

ID = Indonesia

IT = Italy

MX = Mexico

MY = Malaysia

NL = Netherlands

NO = Norway

NZ = New Zealand

PH = Philippines

PL = Poland

PT = Portugal

SA = Saudi Arabia

SE = Sweden

SG = Singapore

SI = Slovenia

TR = Turkey

TW = Taiwan

RU = Russia

VE = Venezuela

ZA = South Africa

1.3

Features

DTE Interface: an RS232 serial interface with hardware handshaking, connected to two 9-
pin female D-connectors.

Line interface: a transformer-coupled telephone line interface with tone and pulse dialling.
The line interface can be used in both 2-wire and 4-wire dial-up and leased line connec-
tions.

Radio interface: a combined interface for connecting either a leased line, or a radio trans-
ceiver.

Both the Line interface and Radio interface can be used for communication over leased
lines.

Indication LEDs: The seven LEDs show the operation status of the modem.

Designed for operation in distribution automation environment.

Содержание 1MRS119000





















Отзывы: