manualshive.com logo in svg

AAVIX GC-1032, Руководство пользователя

Поделиться
Скачать
AAVIX GC-1032 Скачать руководство пользователя страница 4

 

4 

coil’s plug into the search coil jack on the detector’s control 

housing. 

 

Caution:   

 

Do not over-tighten the search coil or use tools such as pliers to 

tighten it. 

 

The search coil’s plug fits into the connector only in one way. Do 

not force the plug and also do not pull on the cable or you could 

damage it. 

5.  Stand and stretch  your arm, holding the metal detector to make the 

search coil above the ground for about 1 to 5 cm. Rotate the stem’s 

lock nut counterclockwise to tighten it. 

 

INSTALLING THE BATTERIES 

Your metal detector is powered by two 9V batteries (not included). 

1. Turn off the power before installing the batteries. 

2. Slide the left and right battery covers off in the direction of the arrow. 

3. Place a 9V battery into the battery compartment matching the polarity 

symbols (+ and -) marked inside.   

Warning: 

 

Dispose of old batteries promptly and properly. Never bury or burn 

them. 

Cautions: 

 

Use only fresh alkaline batteries of required size. 

 

Do not mix old and new batteries or different types of batteries.

 

 

Do not mix alkaline, standard(carbon-zinc), or rechargeable 

(nickel-cadmium) batteries.

 

OPE

N

Содержание GC-1032















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды