AAON LZ Series Скачать руководство пользователя | Manualshive

Страница: 30 / 104

background image

30

Water Connection

Remove  the  shipping  cover  from  the  water
connection  cutout  in  the  post.    Connect  the
supply and return water lines.  The standard
water  connection  is  grooved  end  pipe.    The
connection  size  is  listed  on  the  unit  rating
sheet  along  with  the  designed  volumetric
flow rate.  The maximum operating pressure
for AAON LZ Series unit is 125 psi.  Install
the flashing provided by AAON according to
the  steps  in  Figure  11.    Finished  water
connection will be water tight.

Figure 11 - Water Pipe Flashing Installation

The chiller must be operated only with
liquid flowing through the evaporators.

WARNING

Boilers must be operated only with
liquid flowing through the boiler.

WARNING

PVC  (Polyvinyl  Chloride)  and  CPVC
(Chlorinated  Polyvinyl  Chloride)  are
vulnerable  to  attack  by  certain
chemicals.  Polyolester  (POE)  oils
used

with

R-410A

and

other

refrigerants, even in trace amounts, in
a  PVC  or  CPVC  piping  system  will
result in stress cracking of  the piping
and  fittings.    This  will  result  in
complete piping system failure.

CAUTION

Installing Contractor is responsible for
proper sealing of the water piping and
electrical entries into the unit Failure
to seal the entries may result in
damage to the unit and property.

CAUTION

«
...
28
29
30
31
32
...
»

Содержание LZ Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для LZ Series

Бренд: Cornelius Страницы: 52

York YKEP Series

Бренд: Johnson Controls Страницы: 128

GARDEN WAY Pro line 12183

Бренд: Troy-Bilt Страницы: 36

Бренд: Troy-Bilt Страницы: 32

Бренд: Troy-Bilt Страницы: 48

Бренд: Vito Agro Страницы: 72

Carrier 16LJ Series

Бренд: Sanyo Страницы: 52

Бренд: LG Страницы: 82

Бренд: LG Страницы: 119

Бренд: LG Страницы: 134

Бренд: LG Страницы: 140

Бренд: Troy-Bilt Страницы: 19

Бренд: Split-fire Страницы: 47

Бренд: MTD Страницы: 23

$Texas Mini Tex 204 User Manual preview$

Бренд: Texas Страницы: 18

Бренд: The Handy Страницы: 24

Hyperchill ICE003

Бренд: Parker Hiross Страницы: 28

Бренд: Zanussi Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды