AAON ASM01891 Скачать руководство пользователя страница 13

Страница: 13 / 17

Zone

Two Condenser Head Pressure II Module Technical Guide

Zone

TROUBLESHOOTING

Head Pressure Module Valve / Fan Position Troubleshooting

Head Pressure Module Valve/Fan

Position Troubleshooting

If configured for Water valve:

Aout Signal is 2 to 10 volts.

2 volts = 0% valve position or fully closed

10 volts = 100% valve position or fully open

PWM signal is not used for water valve but does modulate.

At Startup for cooling, valve will open to 75% or 8 volts for 3

minutes then will modulate to try to maintain head pressure

setpoint.

For heating, valve will open and stay at 100%.

If configured for Air Condenser Fan:

Aout Signal is 0 to 10 volts.

Minimum fan speed is 1 volt. (10%)

Maximum fan speed is 10 volts. (100%)

Anything less than 1.5 volts the fan will be off.

PWM signal is 0 to 100%

PWM+ (to ground) will always read 24 vdc.

PWM- (to ground) can be measured for volts dc and this

formula will tell you the percentage signal: (24 – measured

value)/24 (measured value = PWM- to ground)

PWM-

0 volts = 100% fan speed

6 volts = 75% fan speed

12 volts = 50% fan speed

18 volts = 25% fan speed

20.4 volts = 15% fan speed

Above 20.4 volts = 0% fan speed

At Startup for cooling, fan will start at 100% for 3 minutes

and then will modulate to try to maintain head pressure

setpoint.

For heating, fan will run and stay at 100%.

Safeties:

If the head pressure signal is above 500 PSIG, fan will go to

100% (high pressure safety).

If the head pressure signal is below 1 PSIG, fan will go to

100% (assuming bad sensor).

If the head pressure rises 50 PSI above setpoint, the condenser

signal will go to 100%.

Содержание ASM01891


















Результаты поиска

Содержание ASM01891

Отзывы:

Бренды по названию

Популярные бренды

AAON ASM01891, Техническое руководство

Результаты поиска

Содержание ASM01891

Отзывы:

Бренды по названию

Популярные бренды