AAON ASM01695 Скачать руководство пользователя страница 21

Страница: 21 / 43

MODGAS-XWR2 Technical Guide

I/O Map

See

Table 2, this page

to reference the inputs and outputs that

are available on the MODGAS-XWR2 Module.

Analog Inputs

Reset Input (RST IN)

This input is only required when the module is in Stand-Alone

Mode. The Supply Air Temperature Setpoint can be reset by

supplying a 0-10 VDC signal to the RST IN low voltage terminal

block. This reset signal is optional and is only used if you require

resetting of the Supply Air Temperature.

Supply Air Temperature Sensor (SAT)

This input is only required when the module is in Stand-Alone

Mode. The Supply Air Temperature Sensor is the control source.

This sensor has to be installed for the unit to operate. The Supply

Air Temperature Sensor is located in the discharge air stream and

monitors temperature to maintain the Supply Air Temperature

Setpoint.

Binary Inputs

Heat Enable Contact (HEAT EN)

This input is only required when the module is in Stand-Alone

Mode; it is not required when used as an expansion board to other

AAON unit controllers. The Heat Enable input is activated by

a 24 VAC signal. The module will not operate without 24 VAC

being applied to this input terminal when used in a Stand-Alone

Mode.

Proof of Ignition 1 (PO-IGN1)

The Proof of Ignition input is activated by a 24 VAC signal

supplied from the ignition module to enable the modulating

Gas Valve 1 (and the modulating Gas Valve 2 in the 2V1IGN1S

configuration). If the flame does not ignite, the ignition module

will turn off this enable and the MODGAS-XWR2 will turn on

the “No Proof of Flame” Alarm.

Proof of Ignition 2 (PO-IGN2)

The Proof of Ignition input is activated by a 24 VAC signal

supplied from the ignition module to enable the modulating Gas

Valve 2. If the flame does not ignite, the ignition module will

turn off this enable and the MODGAS-XWR2 will turn on the

“No Proof of Flame” Alarm.

Communicating Outputs

Gas Valve Output 1

This communicating output will control the modulating gas

valve. It can detect if the valve is connected and can verify the

valve position.

Gas Valve Output 2

This communicating output will control the modulating gas

valve. It can detect if the valve is connected and can verify the

valve position.

Relay Outputs

RLY1 - Fan Enable

This relay works in conjunction with the Low Speed Fan Relay

(RLY2) to control the speed of the blower motor. When the

MODGAS-XWR2 has heat enabled, this relay closes to bring

the blower on at high speed. The module will activate the Low

Speed Fan Relay (RLY2) to reduce the blower speed as the gas

valve modulates closed.

RLY2 - Low Speed Fan

Depending on the gas valve position, this relay will close to

switch the blower to low speed. The module automatically

switches the blower to low speed as the gas valve modulates

closed in order to maintain proper fuel to air ratios.

RLY3 - Heat 1

Once the MODGAS-XWR2 brings on heat, Heat 1 (RLY3) is

the first stage of heat.

NOTE:

In the 2V2IGN1S configuration, Heat 1 (RLY3)

and Heat 2 (RLY4) are one stage.

Analog Inputs

(RST IN) Reset Signal

(SAT) Supply Temperature

(AUX AI) Not Used

Binary Inputs

(AUX BI) Not Used

(HEAT EN) Heat Enable

Proof of Ignition 1 (PO-IGN1)

Proof of Ignition 2 (PO-IGN2)

Analog Outputs (0-10 VDC)

Fan

Low Speed Fan

Heat 1

Heat 2

Heat 3

Heat 4

Table 2: MODGAS-XWR2 Inputs and Outputs

INPUTS AND OUTPUTS

Inputs and Outputs

Содержание ASM01695












































Результаты поиска

Содержание ASM01695

Отзывы:

Бренды по названию

Популярные бренды

AAON ASM01695, Техническое руководство

Результаты поиска

Содержание ASM01695

Отзывы:

Бренды по названию

Популярные бренды