manualshive.com logo in svg

A&D RA3100 Omniace, Простое руководство пользователя

Поделиться
Скачать
A&D RA3100 Omniace Скачать руководство пользователя страница 34

4.Configuring Measurement - 4.3.Recording Setup 

 

34 

1WMPD4004445 

 

4.3.  Recording Setup 

4.3.1.  Setup the Sampling Speed 

 

An image of the waveform recorded on the selected recording device (PRINTER, SSD, or MEMORY) is 
displayed on the waveform monitor.   
The sampling speed of the image waveform recorded on the selected recording device is displayed on 
the left edge of the control bar. 

 
 
 
 
 
 

An image of the waveform 
recorded on the selected 
device is displayed on the 
waveform monitor. 

 
 
 
 
 
 
 

Tap to display the selectable sampling speed table. 

 
 
 
 
 
 

Tap the sampling speed to 
display the waveform sampled at 
that speed. 

  Drag the table to the left or right 

to display the hidden speed table. 

 
 

When the sampling speed is decided, tap  OK   on the right edge to close the table. 

 
 
 

 

Содержание RA3100 Omniace













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды