manualshive.com logo in svg

A&D RA3100 Omniace, Простое руководство пользователя

Поделиться
Скачать
A&D RA3100 Omniace Скачать руководство пользователя страница 26

2.Pre-Measurement Procedures - 2.2.Turning the Power On/Off 

 

26 

1WMPD4004445 

Step 4.  Turn the    Power    switch of the product on.   

When the power switch on the operation panel of the 
product is turned on, the green LED lights up and the power 
turns on. 

  NOTE   

  Standby current flows to this product when the AC power 

cable is connected to the power outlet.   
Remove the power cable when the product will not be used 
for an extended period of time. 

 

 Power   switch 

 

2.2.3.  Confirming Normal Startup 

 

The monitor screen of the RA3100 is displayed about one minute 
after turning the power on. 

  NOTE   

  Do not touch the touch panel until the waveform monitor is 

displayed. Doing so may lead to erroneous operations. 

  Immediately after purchase or initializing the main unit, 

measurement is turned off for all channels and no waveform is 
displayed. 

 
 

2.2.4.  Preparing for More Precise Measurements 

 

Warm up the product for about 60 minutes after turning on the power in order to perform more precise 
measurements.   
After the warm up is complete, perform "

Zero adjust

" of the input modules.   

See "

4.Setup Measurement

".   

This completes the preparations for measurement. 

 
 

2.2.5.  Turning Off the Power 

Step 1.  When the    Power    key on the operation panel is pressed 

while the power is on, the shut down process starts and the 
[Shut down] dialog box indicated below is displayed on the 
center of the screen. Tap the  OK   key to shut down the 
product. Tap the  Cancel   key to continue without turning off 
the power.   
If the    Power    key is pressed again while the [Shut down] 
dialog box is displayed, the product automatically shuts down. 

 

CAUTION

 

  Make sure to shut down the product to turn off the power, as directly removing the power cable from 

the power outlet without shutting down can damage the files in the internal storage. 

 

 

Содержание RA3100 Omniace













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды