manualshive.com logo in svg

A&D RA3100 Omniace, Простое руководство пользователя

Поделиться
Скачать
A&D RA3100 Omniace Скачать руководство пользователя страница 25

 

2.Pre-Measurement Procedures - 2.2.Turning the Power On/Off 

1WMPD4004445 

25 

2.2.  Turning the Power On/Off 

2.2.1.  Connecting the AC Power Cable 

 

Be sure to check the following points before connecting the AC power cable to this product. 

  Make sure that the power supply matches the rating indicated on the rating plate attached to this 

product. 

  Ensure amp or interface units are inserted securely. 

WARNING

 

  This product must be grounded before turning on the power. 
  This grounding protection is for the safety of this product, as well as for that of the user and 

peripheral equipment. 

  If the AC power cable that comes with this product is connected to a 3-pin power outlet equipped 

with a protective conductor pin, the product is automatically grounded. 

  Do not use an extension cable without protective grounding. 
  Do not use this product when protective grounding cannot be performed using a power outlet that 

matches the supplied AC power cable. 

 

2.2.2.  Turning On the Power 

Step 1.  Perform the check indicated below. 

<Items to check before turning on the power> 

  Is this product installed in a safe location? 
  Is the usage environment OK? 
  Is the top of the touch panel free from any writing implements or tools, etc.? 

 
Step 2.  Upon confirming that all of the above check items are fine, connect the inlet side of the AC power 

cable to the AC socket of this product. 

 
Step 3.  Connect the plug of the AC power cable to the power outlet. 
 
 
 
 
 
 
 
 
 

Power outlet with ground terminal 

 

Inlet side   

to AC socket 

Plug to   

power outlet 

 

 

AC power cable 

 

 

 

Содержание RA3100 Omniace













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды