AAF RotoClone W Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 46

background image

7

RotoClone

®

W

© 2015 American Air Filter Company, Inc. Any use of the text or images

this document contains, without permission of American Air Filter

Company, Inc., is prohibited. RotoClone, AAF, REDClean, REDFiltration,

and Reliable Efficient Durable are registered trademarks of American Air

Filter Company, Inc. d/b/a AAF International.

including, but not limited to, the necessity or effectiveness of explosion hazard
equipment or to the design, installation, operation, and performance of such

equipment.

The basic standards for dealing with explosive dust applications are

published by the National Fire Protection Agency (“NFPA”). The user shall be fully

conversant with the provisions of the particular codes and standards that apply to
the specific application and equipment used, and shall comply in full with all of the

requirements of the applicable codes and standards.

2.3.1

NFPA 654 and referenced codes and standards

The owner shall review and comply with

NFPA 654: Standard for the

Prevention of Fire and Dust Explosions from the Manufacturing,

Processing, and Handling of Combustible Particulate Solids

, and those other

documents referenced therein. NFPA 654 pertains to “all phases of manufacturing,

processing, blending, conveying, repackaging, and handling of combustible
particulate solids or hybrid mixtures, regardless of concentration or particle size,

where the materials present a fire or explosion hazard”. The purpose of the
standard “is to prescribe technical requirements for safety to life and property

from fire and explosion and to minimize the resulting damage from a fire or
explosion”. The user shall be fully conversant with the provisions of NFPA 654 and

shall comply in full with all of its requirements and those of all applicable
referenced codes and standards.

Note that NFPA 654 does not apply to the specific applications or materials

covered by the following documents unless specifically referenced by those

documents. Review this list to determine if any of these codes and standards apply
to the particular use for which the RotoClone

®

W will be employed. If such is the

case the appropriate documents shall be reviewed and complied with in full.

NFPA 30B, Code for the Manufacture and Storage of Aerosol Products, 2015
edition.

NFPA 33, Standard for Spray Application Using Flammable or Combustible

Materials, 2011 edition.

NFPA 61, Standard for the Prevention of Fires and Dust Explosions in
Agricultural and Food Processing Facilities, 2013 edition.

«
...
5
6
7
8
9
...
»

Содержание RotoClone W















































Отзывы:

Нет отзывов

Похожие инструкции для RotoClone W

FlexPAK Standard

Бренд: Nederman Страницы: 369

Бренд: Jet Страницы: 20

Бренд: Nation Flooring Equipment Страницы: 22

Бренд: Shop fox Страницы: 60

Бренд: Delabie Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды