background image

N e t w o r k   Ap p l i a n c e  

F W S - 7 1 5 0

 

 

Chapter 3 Award BIOS Setup   

3-3 

3.2 Award 

BIOS 

Setup 

Awards BIOS ROM has a built-in Setup program that allows users 
to modify the basic system configuration. This type of information is 
stored in battery-backed CMOS RAM so that it retains the Setup 
information when the power is turned off. 

Entering Setup 

Power on the computer and press <Del> immediately. This will 
allow you to enter Setup.   

Standard CMOS Features 

Use this menu for basic system configuration. (Date, time, IDE, 

etc.) 

Advanced BIOS Features 

Use this menu to set the advanced features available on your 

system. 

Advanced Chipset Features 

Use this menu to change the values in the chipset registers and 

optimize your system performance. 

Integrated Peripherals 

Use this menu to specify your settings for integrated peripherals. 

(Primary slave, secondary slave, keyboard, mouse etc.) 

Power Management Setup 

Use this menu to specify your settings for power management. 

(HDD power down, power on by ring, KB wake up, etc.) 

PnP/PCI Configurations 

This entry appears if your system supports PnP/PCI. 

 

Содержание FWS-7150


























































Отзывы: