A.R.I. Eliptix R-30 R 2W Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 21

A.R.I. Eliptix R-30 R 2W Скачать руководство пользователя страница 1

R-30 R .IOM.ENG01

R-30 R 2W

Pressure Reducing Control Valve
2 Way

The following is a step by step narrated description of the Eliptix R-

30

R

2

W Pressure Reducing Valve

installation, operation and maintenance processes.
The A.R.I. R-

30

Series is a line of metal, diaphragm-operated, hydraulic control valves.

The valves are suitable for installation in agriculture, water transmission and waterworks systems
for irrigation, landscape and infrastructure applications.
The R-

30

series has an innovative elliptic shaped diaphragm that integrates well with a wide variety

of regulating control pilots, solenoids and control accessories.
They are compatibility designed for water level control, flow control, electric & remote control as
well as pressure reducing & pressure sustaining operation.

The R-

30

Pressure Reducing Valve is designed to reduce a higher upstream pressure to a preset

lower downstream pressure and to maintain this constant pressure regardless of flow-rate or
upstream pressure fluctuations.

1
2
3
...
»

Содержание Eliptix R-30 R 2W






















Отзывы:

Нет отзывов