background image

6 www.hotwater.com 

Thank You

 for purchasing this water heater. Properly 

installed and maintained, it should give you years of trouble 
free service.

Abbreviations found in this Installation and Operating 
manual:

CSA - Canadian Standards Association
ANSI - American National Standards Institute
NFPA - National Fire Protection Association
ASME - American Society of Mechanical Engineers
GAMA - Gas Appliance Manufacturer’s Association
UL - Underwriters Laboratories Inc.
AHRI - Air Conditioning, Heating and Refrigeration 
Institute.

This gas-

fi

 red water heater is design certi

fi

 ed by CSA 

International, under 

Water Heater Standard ANSI 

Z21.10.1 • CSA 4.1

 (current edition).

 QUALIFIED INSTALLER OR SERVICE AGENCY

Installation and service of this water heater requires ability 
equivalent to that of a Quali

fi

 ed Agency (as de

fi

 ned  by 

ANSI below) in the 

fi

 eld involved. Installation skills such 

as plumbing, air supply, venting, gas supply and electrical 
supply are required in addition to electrical testing skills 
when performing service.

ANSI Z223.1 2006 Sec. 3.3.83

: “Quali

fi

 ed Agency” - “Any 

individual, 

fi

 rm, corporation or company that either in 

person or through a representative is engaged in and is 
responsible for (a) the installation, testing or replacement 
of gas piping or (b) the connection, installation, testing, 
repair or servicing of appliances and equipment; that 
is experienced in such work; that is familiar with all 
precautions required and that has complied with all the 
requirements of the authority having jurisdiction.”

If you are not quali

fi

 ed (as de

fi

 ned by ANSI above) and 

licensed or certified as required by authority having 
jurisdiction to perform a given task, do not attempt to 
perform any of the procedures described in this manual. 
If you do not understand the instructions given in this 
manual do not attempt to perform any procedures outlined 
in this manual.

 PREPARING FOR THE INSTALLATION

Read the “General Safety Information” section of this 
manual 

fi

 rst and then entire manual carefully. If you 

don’t follow safety rules, the water heater will not 
operate properly. It could cause DEATH, SERIOUS 
BODILY INJURY AND/OR PROPERTY DAMAGE.
This manual contains instructions for installation, 
operation, and maintenance of the gas-

fi

 red  water 

heater. It also contains warnings throughout the 
manual that you must read and be aware of. All 
warnings and instructions are essential to proper 
operation of the water heater and your safety. Since 

1.

we cannot put everything on the 

fi

 rst few pages, 

READ ENTIRE MANUAL BEFORE ATTEMPTING TO 
INSTALL OR OPERATE THE WATER HEATER

.

The installation must conform with these 
instructions and local code authority having 
jurisdiction. In absence of local codes, installation 
must comply with current editions of the 

National 

Fuel Gas Code, ANSI Z223.1/NFPA 54

 and 

National Electrical Code, NFPA 70

. All documents 

are available from:

CSA International,
8501 East Pleasant Valley Road,
Cleveland, Ohio, United States
44131-5575.

NFPA documents are also available from:
National Fire Protection Association,
1 Batterymarch Park,
Quincy, MA 02269.

The water heater, when installed, must be electrically 
grounded in accordance with the local codes or in the 
absence of local codes: the 

National Electrical Code 

(NFPA 70)

.

If after reading this manual you have any questions or 
do not understand any portion of the instructions, call 
the local gas utility or the manufacturer whose name 
appears on the rating plate.
Carefully plan the place where you are going to put 
the water heater. Correct combustion, vent action, and 
vent pipe installation are very important in preventing 
death from possible carbon monoxide poisoning and 

fi

 res (see Figures 15 & 16). Examine the location to 

ensure the water heater complies with the “Locating 
the New Water Heater” section in this manual.
For installation in California, this water heater must 
be braced, anchored, or strapped to avoid falling or 
moving during an earthquake. See instructions for 
correct installation procedures. Instructions may be 
obtained from:

California Of

fi

 ce of the State Architect,

400 P Street,
Sacramento, CA 95814.

Massachusetts Code requires this water heater to be 
installed In accordance with 

Massachusetts 248-

CMR 2.00: State Plumbing Code and 248-CMR 
5.00

.

Complies with California Health and Safety code 
116875 (known as AB-1953) and with weighted 
average maximum of 0.25% lead.

2.

3.

4.

5.

6.

7.

8.

INTRODUCTION

Содержание Residential Gas Water Heaters





























































Отзывы: