background image

17

VENT CONNECTIONS TO BLOWER ASSEMBLY

Figure 15 shows the typical vent connections.

FIGURE 15.

VENTING AND INSTALLATION

Plan the layout of the vent system from the vent termination to the water 
heater considering all of the 90° and 45° elbows plus the number of 
feet of pipe that would be needed to install the total vent system.  Note: 
The inlet connection to the blower requires a minimum 3" long x 3" 
Schedule 40 PVC pipe.  The water heater must be vented to the 
outdoors as described in these instructions. DO NOT connect this water 
heater to an existing vent or chimney. It must be vented separately 
from all other appliances. The 

fi

 ttings, other than the supplied Vent 

Termination should be equivalent to the following: PVC (Schedule 40, 
DWV, ASTM D-2665), CPVC (Schedule 40, DWV, ASTM F-438), ABS 
(Schedule 40 DWV, ASTM D-2661). 
The cement used should be as recommended by the vent 
pipe manufacturer. See the instructions in the “VENT PIPE 
PREPARATION” section of this manual for the proper method of 
cutting and cementing the PVC pipe and 

fi

 ttings. 

All vent gases must be completely vented to the outdoors of the 
structure (dwelling). When determining the installation location for 
a power direct vent water heater, snow accumulation and drifting 
should be considered in areas where applicable.
IMPORTANT: DO NOT common vent this water heater with any 
other appliance.

FIGURE 16.

Horizontal runs must be securely supported at 3 1/2 foot (1 m) 
intervals and vertical runs supported at 5 foot (1.5 m) intervals.

FIGURE 17.

VENTING THROUGH AN OUTSIDE WALL

A. All 75 Gallon Models

In the carton is supplied: 

1.  Two 3” inlet and outlet PVC Schedule 40 - 45° vent caps.

2.  One 3” CPVC Schedule 80 - 90° elbow; used to connect the 

outlet

 

vent pipe to the water heater when the 

outlet

 vent pipe is to be 

turned horizontally directly off the blower.

3.  One 5’ (1.5 m) section of 3” CPVC Schedule 40 

outlet

 vent pipe. 

(More may be required and must be purchased locally.)

Note: A 2-5/8" (66.675 mm) long section of CPVC pipe can be cut 
from the 5' (1.5 m) section of 3" CPVC Schedule 40 vent pipe.  
This is used to connect the 

outlet

 vent pipe elbow to the water 

heater when the 

outlet

 vent pipe is to be turned horizontally 

directly off the blower.

FIGURE 18.

Requirements:
1.  The water heater requires its own (separate) venting system.
2. 

Only

 3” CPVC Schedule 40 piping and 

fi

 ttings are acceptable 

materials on the 

fi

 rst 

fi

 ve feet of the 

outlet

 vent system.

3. 3” PVC, ABS, or CPVC Schedule 40 piping and 

fi

 ttings  are 

acceptable materials for the 

inlet

 vent system and for the 

outlet

 

vent system after the 

fi

 rst 

fi

 ve feet. 

Содержание ProMax GPDX-50





































Отзывы: