background image

13

1.  1 square inch per 3000 Btu/hr (733 mm

2

 per kW) of the total 

input rating of all appliances located in the enclosure, and

2.  Not less than the sum of the areas of all vent connectors in the space.

outdoor aIr throuGh two horIZontal ducts

fIGure 6.

The confined space shall be provided with two permanent horizontal 

ducts, one commencing within 12 inches (300 mm) of the top and 

one commencing within 12 inches (300 mm) of the bottom of the 

enclosure. The horizontal ducts shall communicate directly with the 

outdoors. See Figure 6.

Each duct opening shall have a minimum free area of 1 square inch 

per 2,000 Btu/hr (1100 mm

2

 per kW) of the aggregate input rating of 

all appliances installed in the enclosure.

When ducts are used, they shall be of the same cross sectional area 

as the free area of the openings to which they connect. The minimum 

dimension of rectangular air ducts shall be not less than 3 inches.

aIr froM other Indoor spaces

fIGure 7.

The  confined  space  shall  be  provided  with  two  permanent 

openings, one commencing within 12 inches (300 mm) of the top 

and one commencing within 12 inches (300 mm) of the bottom of 

the enclosure. See Figure 7.

Each opening shall communicate directly with an additional room(s) 

of  sufficient  volume  so  that  the  combined  volume  of  all  spaces 

meets the criteria for an Unconfined Space.

Each opening shall have a minimum free area of 1 square inch per 

1,000 Btu/hr (2200 mm

2

 per kW) of the aggregate input rating of 

all appliances installed in the enclosure. Each opening shall not be 

less than 100 square inches (645 cm

2

).

Содержание Gdhe 50

























































Отзывы: