A-Maize-Ing Heat NRP620-10 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 87

background image

NRP620-9 OMEPAPV20161017 (ENGLISH) REV 1

Page 17 of 42

FURNACE UNPACKING AND SET UP

Your furnace was shipped from the factory with a “FURNACE PACKAGE” packing list.  That document
includes the part number and serial number.  Locate that list and check the contents of the packaging
to ensure all items were delivered.  The items you will have are in the list below.

A.

FURNACE

B.

HOPPER (Model 14 or Wedge 200)

C.

HOPPER LID

D.

HOPPER LEGS AND CROSS BEAMS (Model 14 hopper only)

E.

HIGH FIRE TIMER (SET @ 30 SEC. ON AND 30 SEC. OFF) LOW FIRE TIMER (SET @ 2

MIN. ON 12 MIN. OFF) (already installed on Wedge 200)

F.

DRAFT CONTROL W/COLLAR

G.

FURNACE PARTS BAG (INCLUDES: wooden handles x 4, orange wire nuts x 3, ¼” x

½” self-tapping screw x 3, connecting tube x 1 and owner’s manual)

H.

HOPPER HARDWARE BAG (Model 14 hopper only) (INCLUDES: 5/16” X ½” hex head

cap screws x 16 and 5/16” hex nuts x 16)

I.

BURNPOT AUGER (already installed)

J.

BIN AUGER (already installed on Wedge 200)

K.

FILTER (already installed)

L.

POKER

M.

HOSE CLAMP (already installed on Wedge 200)

N.

VIBRATOR (not applicable with the Wedge 200, already installed on Model 14 Bin)

1.

After removal of shipping materials, remove the furnace from the pallet by removing the three

shipping screws securing the furnace to the pallet. One (1) screw is accessible by removing the

filter door. The remaining two (2) are removed from under the pallet.

2.

Remove the Furnace Assembly Package from the combustion chamber.

3.

Slide wooden handles on door handle, door safety handle, and heat exchanger scraper rod.

«
...
60
61
62
63
64
...
»

Содержание NRP620-10
























































































Отзывы:

Нет отзывов

Похожие инструкции для NRP620-10

Бренд: Valley Comfort Systems Страницы: 26

*MH81405D Series

Бренд: Goodman Страницы: 48

Бренд: SummerAire Страницы: 5

Бренд: Whirlpool Страницы: 8

Бренд: Whirlpool Страницы: 16

Бренд: Whirlpool Страницы: 28

Бренд: Carbolite Страницы: 16

Бренд: Carbolite Страницы: 17

Бренд: Carbolite Gero Страницы: 40

Бренд: York International Страницы: 40

Бренд: York International Страницы: 40

Бренд: York International Страницы: 42

Бренд: York International Страницы: 46

Бренд: Wood master Страницы: 72

Бренд: York Страницы: 16

Бренд: Zircar Страницы: 13

Бренд: Bryant Страницы: 8

Бренд: Bryant Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды