background image

Rapid toasteR VCt-250

5

P/N 00837 Rev. L 03/07 

McDonald’s

Rear Conveyor Cover Assy.

Spacer

Acorn Nut

Screw

Tensioner Assy.

Teflon Tape

figure 19. Replacing Roller tensioner assembly.

MaiNteNaNCe (continued)

install New Release sheet (monthly)

  

.

  Fold a new Release Sheet in half, creasing the  

fold only with your fingers (Figure 7), and place 

it over the Platen. Allow the conveyor to draw it 

into place and verify that it is positioned properly 

(Figure 9).

Note: Use only your fingers to crease the fold. 

do Not use any metal, wood, or plastic devices 

as they will damage the Release sheet.  additional 

Release sheets can be obtained through your 

authorized service agency. 

  2.  Re-install the Bun Feeder and Bun Chute and 

allow the toaster 30 minutes to warm up.

figure 17. folding Release sheet

Lay sheet on a flat surface

Fold over so ends meet

Press lightly with finger to 

form crease

CaUtioN

Failure to use Release Sheets will result in damage to 

the unit and loss of warranty coverage.

adjusting, Measuring and/or Replacing 

Roller tensioner assemblies

Note: Measure the Roller tensioners. they should 

be 13/16” (2.1 cm), or the height of a U.s. Nickel 

coin from the bottom of the roller to the inner 

Conveyor Cover (figure 18) and adjust or replace 

them accordingly.  if the tensioners have been 
damaged, they should be replaced:

  .  Remove screws from acorn nuts (Figure 9) and 

remove the old Roller Tensioner assembly.

Checking the temperature of the bun 

landing area

iMpoRtaNt: if the toaster is equipped with a bun 

buffer landing Zone (bblZ), you MUst remove 

the bblZ befoRe performing the temperature 

measurement in step 1 below.  this temperature 

measurement is intended to be taken WithoUt the 

bblZ attached to the toaster.

  .  Take the temperature of the Bun Landing Area at 

its center directly in front of the Bun Chute with 

a Pyrometer/Surface Temperature (grill) Probe. 

The minimum acceptable temperature is 30° F 

(54° C). If the temperature is less, contact your 

Authorized Service Agency or the Technical 

Service Department of A.J. Antunes & Co. at 877-

392-7854 (for the U.S. & Canada only) or 630-

784-000.

  2.  If a Bun Buffer Landing Zone was removed from 

the toaster in Step , re-attach it after completing 

Step .

figure 18. Measuring Roller tensioner

  2.  Replace Roller Tensioner assembly and reas-

semble. 

  3.  Make sure the spacers are placed inside the 

tensioner arm.  The spacers are smaller than the 

holes to allow the tensioner to pivot freely.

  4.  Set the Bun Thickness Compression Controls 

according to Table .  Plug in the power cord and 

turn unit on.

Note: Refer to table 1 as well as figures 2a and 2b 

in the operation section of this manual.

Содержание VCT-250





























Отзывы: