A.J.Antunes 9100480 Скачать руководство пользователя страница 14

Страница: 14 / 20

MIRACLE STEAMER

P/N 1010456 Rev. C 08/12

A.J. Antunes & Co.

Problem

Possible Cause

Corrective Action

Unit heats but there

is little or no steam

produced

and/or

The product requires

more steaming than

usual.

Filter Strainer is restricted.

Check and clean the Filter Strainer as described in

the Maintenance section of this manual.

Unit is not being cleaned properly

(daily/monthly).

Clean unit daily and monthly as described in the

Maintenance section of this manual.

Programming and/or SHO, H2O

values were adjusted/changed

improperly.

Reprogram the SHO and H2O values as described

in the Programming section of this manual.

Insufficient or excessive calcium/

mineral deposits on the Generator

surface.

Verify a thin layer of calcium/mineral deposits is

present on the Generator surface. Refer to the

Maintenance section of this manual.

Generator surface is bare.

Generator surface must have a thin calcium/min-

eral coating for proper steaming. Refer to the

Maintenance section of this manual.

Generator Steam Ports are

restricted.

Clean the Steam Ports as described in the

Maintenance section of this manual.

Generator Cover is warped or loose. Verify that the Generator Cover’s Wing Nut is tight.

If noticeable steam escapes around the Generator

Cover, replace the cover.

Generator Diffuser is missing.

Install Generator Diffuser or replace if missing.

Generator surface temperature is too

low.

Verify Generator surface temperature to be 380–

420°F (193–215°C).

Excessive con-

densation in Food

Compartment.

Programming and/or SHO and H2O

values were adjusted improperly.

Reprogram the SHO and H2O values as described

in the Programming section of this manual.

Steam coming out

around top covers or

sides.

Generator Cover’s Wing Nut is

loose.

Tighten Wing Nut.

Generator Cover is warped.

Replace Generator Cover.

TROUBLESHOOTING (continued)

Содержание 9100480





















Результаты поиска

Содержание 9100480

Отзывы:

Похожие инструкции для 9100480

Бренды по названию

Популярные бренды

A.J.Antunes 9100480, Руководство пользователя

Результаты поиска

Содержание 9100480

Отзывы:

Похожие инструкции для 9100480

Бренды по названию

Популярные бренды