909 909004DEC Скачать руководство пользователя страница 11

11

•  

Do not use an extension cord unless it is absolutely 

necessary. The use of an improper extension cord could 

cause the risk of fire, electric shock or electrocution.

•  

Never attempt to connect two chargers together.

•  

Do not charge batteries or use the tool and battery pack 

in locations where the temperature may be below 0°C or 

exceed 40°C such as alongside sheds or metal structures.

•  

The battery can be charged or operated at temperatures 

between 0° C and 40° C.

NEVER CHARGE YOU LITHIUM ION BATTERY BELOW 

OR ABOVE TEMPERATURES RECOMMENDED 

OTHERWISE FIRE OR SERIOUS DAMAGE TO THE 

BATTERY PACK MAY OCCUR. 
The most suitable temperatures to charge the battery pack 

are between 20 - 25° C.

•  

If you wish to charge a second battery pack, unplug the 

charger from the mains supply and leave it for at least  

15 minutes. After this time you can charge a second 

battery pack.

Additional safety instructions related  

to the battery pack and battery safety

•  

Use only the 909 batteries supplied with the 909 Tool or 

909-approved replacements.

•  

Do not use the battery to power any device other than  

the 909 tool it was sold with.

•  

Charge the battery only with the 909 charger supplied 

with the tool or 909-approved replacements and 

according to the instructions in the 909 Instruction 

Manual.

•  

Do not charge the battery in a place where static 

electricity is generated nor let the battery touch something 

that is statically charged.

•  

The battery can be stored at temperatures between  

0° C and 40° C.

NEVER STORE OR LEAVE YOUR LITHIUM ION BATTERY 

IN TEMPERATURES OVER THAT RECOMMENDED 

OTHERWISE FIRE MAY OCCUR. 
Do NOT store the Lithium Ion battery anywhere that 

the temperature can easily reach higher temperatures 

than recommended - this includes garden type sheds, 

and Vehicles where the inside temperature can climb 

to dangerous levels in the direct sunlight and on high 

temperature days. THINK BEFORE LEAVING YOUR 

LITHIUM ION BATTERY PACK IN STORAGE.

•  

The battery can be charged or operated at temperatures 

between 0° C and 40° C.

NEVER CHARGE YOU LITHIUM ION BATTERY BELOW 

OR ABOVE TEMPERATURES RECOMMENDED 

OTHERWISE FIRE OR SERIOUS DAMAGE TO THE 

BATTERY PACK MAY OCCUR. 
The most suitable temperatures to charge the battery pack 

are between 20 - 25° C.

•  

Always allow the battery pack to cool down after charging, 

do not place it in a hot environment such as  

a metal shed or open trailer left in the sun.

Содержание 909004DEC






















Отзывы: