Copyright © 7thSense Design Ltd : M746-3
March 2023
Specification
Environmental Characteristics
Operating
Non-operating
Temperature
+15 to +30
°
C
-10 to +50 °C
Humidity (non-condensing)
10 to 90%
5 to 95%
Altitude
≤
2000 m
≤
10000 m
End of Service Life
Dispose of the equipment and any components in accordance with all local and
national safety and environmental requirements.
Caution: risk of explosion or leakage
of flammable liquids or gas.
Any batteries should not be subject to extremely low pressure,
extremely hot environments, disposed of in fire or mechanically crushed or cut.
Regulatory Compliance Statements
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with this user guide, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at their own expense.
European Union
This is a Class A product. In a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.
R-Series 10 Server
Hardware User Guide
Customer Support Portal: https://portal.7thsense.one
Support
If your R-Series 10 server was purchased through one of our regional distributors, please
contact your supplier directly for support.
Visit our customer support portal where you can find a wide range of support documentation
and video tutorials, together with contact information.
Warranty
Standard warranty is 24 months, return-to-supplier. Please contact your supplier if you require
an extended warranty. Please ask for instructions and request authorisation before returning a
server to your supplier.
Operating Instructions
Operating instructions for your server can be found in the Online User Guides section of the
customer support portal.
Handling and Installation
Unpacking
Unpack your server carefully onto a clean and level surface and examine it for any signs of
transit damage. Contact your supplier immediately if anything appears to be damaged, or any
parts missing. Please retain all packaging in case of future need to return a server.
Lifting
The weight is stated below and on the server’s product label. R-Series 10 require a two-person
lift, especially when manoeuvring into a rack. Observe your internal manual handling
recommendations to avoid injury.
Rack mounting
The fascia panel must be removed before mounting. Remove the two small retaining screws
bottom left and right, and then pull the fascia away. Refit the fascia after mounting.
3U units are supplied with rack mount slide rails and fixings, installation instructions are
included with the slide rails.
Ensure that each server is properly secured to the rack cabinet.
Rack stability warnings:
•
Ensure the rack is stable (e.g. bolted to the floor) before sliding out the server.
•
Do not place objects on equipment projecting from a rack (e.g. do not use as a shelf).
•
Only slide out one piece of equipment from the rack at a time.
Specification
Rating/Description
Notes
Rackmount Dims (H
×
W
×
D)
3U
×
483 mm
×
620 mm
Rackmount weight (approx.)
22 kg
Dual Redundant Power Supply
100-240 V 8 A, 50-60 Hz Autoranging, IEC 60320 inlets
Power
800 W
Cooling
Forced air
Front inlets, rear exhaust
7thSense Design Ltd
: 2 The Courtyard, Shoreham Road, Upper Beeding, BN44 3TN, UK
www.7thsense.one
