3W Xtra Fun II 230 Скачать руководство пользователя

Страница: 14 / 16

Programming RC

We recommend the use of a modern computer
system.

Here we recommend the following order of
programming to you:

Servo directions

• Elevator

highly - pull / down - press

• Rudder

right - left

• Aileron

right: re high - le down
left: le high - re down

• Throttle

idle - full throttle

Rates

Rates and Expow vary strongly after personal preferences. We recommend the
following set up for the first flight: :

Throttle

• adjust idle - full throttle

Aileron

• Aerobatics:

1.6 in

Expo: 50 %

• 3D:

maximal

Expo: 40 %

Elevator

• Aerobatics:

1.2 in

Expo: 60 %

• 3D:

maximal

Expo: 40 %

Rudder

• Aerobatics:

1.9 in

Expo: 50 %

• 3D:

maximal

Expo: 40 %

EXPO rates (+) for Graupner / JR systems (-) for Robbe / Futaba systems

Xtra Fun II 230

Flight preperation

Содержание Xtra Fun II 230

















Результаты поиска

Содержание Xtra Fun II 230

Отзывы:

Похожие инструкции для Xtra Fun II 230

Бренды по названию

Популярные бренды

3W Xtra Fun II 230, Инструкция по сборке

Результаты поиска

Содержание Xtra Fun II 230

Отзывы:

Похожие инструкции для Xtra Fun II 230

Бренды по названию

Популярные бренды