background image

3W 42i Engine Manual

more infos: www.3w-modellmotoren.de

Warning!

Failing to read and follow all of the instructions in this manual can lead to unsafe conditions and

damaged equipment. Here are some examples:

 Unbalanced propellers can damage the engine's ball bearings, needle bearings, even

cause the crankshaft to break

 Incorrectly drilled propellers can lead to sheered propeller bolts further leading to accidents

and crashes

 Loose propeller bolts can also lead to sheered propeller bolts further leading to accidents

and crashes. Check these bolts before starting your engine.

 Flipping the prop with your hand or fingers can lead to serious accidents! Always use a

rubber stick to start the engine!

 Not having the plane secure can be lead to serious accidents. Depending on its size use

one, two, or more helpers to secure your model. Always tell your helpers to be ready for

the model to start at full power. Remember, these engines have a high power output.

 Do not put your finger(s), any items, or any other parts of the body into the rotating propeller.

 Never tune the carburetor whilst engine is running! Stop the engine. Tune the carburetor

and start the engine again. Repeat this procedure until the carburetor is properly tuned.

 Make sure that no gasoline will be splashed into the hot muffler(s).

 Only 3W mufflers, or mufflers authorized by 3W with an acceptance (test) number, should

be used.

 Only 3W-ignition systems should be used for proper operation.

Important:

Using unauthorized products or failing to follow the instructions in this manual will void your

warranty immediately.

Содержание 42i



















Отзывы: