【
Communication Connector
】
PD101-12V-15W
provides 1*10/100M POE ports, 1*10/100M
ports.
10/100BaseT(X) Ethernet port
The pinout of RJ45 port display as below, connect by UTP or
STP. The connect distance is no more than 100m. 100Mbps is used
120
Ω
of UTP 5 , 10Mbps is used 120
Ω
of UTP 3,4,5.
RJ 45 port support automatic MDI/MDI-X operation. can
connect the PC, Server, Converter and HUB .Pin 1,2,3,6
Corresponding connection in MDI. 1→3,2→6,3→1,6→2 are used
as cross wiring in the MDI-X port of Converter and HUB.
10Base-T/100Base-TX are used in MDI/MDI-X, the define of Pin
in the table as below.
NO.
MDI signal
MDI-X signal
1
TX+
RX+
2
TX-
RX-
3
RX+
TX+
6
RX-
TX-
4
、
5
、
7
、
8
—
—
Remark
：“
TX
±”
Transmit Data
±，“
RX
±”
Receive Data
±，“—”
Not Use
。
MDI (straight-through cable)
MDI-X (Cross over cable)
MDI/MDI-X auto connection makes PD101-12V-15W easy
to use for customers without considering the type of network cable.
【
LED Indicator
】
PD101-12V-15W indictor light on the front panel. the
function of each LED is described in the table as below.
System Indication LED
LED
State
Description
PWR
ON
Power is being supplied to
power input PWR input
OFF
Power is not being supplied
to power input PWR input
【
Installation
】
Operation Cautions
1)
Don’t stock the device in damp environment or near
water, to avoid water or moisture penetrating into the
inner device.
2)
Don’t put the device on a unstable box or desk, the
device will get damaged from falling.
3)
Please check and make sure the operation voltage is
meet the voltage standard marked on the device surface
before the next steps.
4)
Please use a grounded three-hole power socket in the
rack or desk mounting, to mitigate damage caused by
electro-static discharge or lightning stoke.
5)
Keep the device far from heat sources, strong power
radio transmitters and radar transmitters.
6)
Similar with other electrical products, the semiconductor
chip in device will get damaged when open and shut off
the power frequently. Please restart the device 3~5
seconds(or longer) after the power is shut off.
7)
Please pull out the power plug before cleaning the
device. Don’t wipe the device with wet cloth or clean the
device with liquid.
8)
To guarantee a long operation life, the device can only
be used in indoor and in ventilated & dry environment.
And to get a good heat dissipation, please reserve a
space over 10CM around the device.
POESplitter Operation Instruction
1)
Connect “ Power+Data”port on POE splitter with a
RJ45 cable, which connected with far-end POE switch
or POE injector on the other end. When one of the three
voltage LED indicator(5V/9V/12V) is on, the
connection is successful.
2)
Please choose right voltage state according to your POE
PDs, the default voltage state is 5V, you can slide the
switch to change to 9V or 12V.
3)
Connect the provided DC power cord to the“Power
OUT” port on the POE splitter, and connect the other
end to the POE PDs with right plugs( 4 types universal
plugs for your option).
4)
Please connect one end of provided RJ 45 cable to the
“Data OUT” port of POE splitter, and connect the other
end to the data in port of POE PDs.
N
ote
：
Please choose correct Splitter voltage output state
according to the voltage requirement of your PDs, or the PDs
will get damaged. The default voltage output is 5V.
【
Specification
】
Technology:
POE Standard: IEEE802.3af/at
1
8
