The device provides LED indicators to monitor its operating
status, which has simplified the overall troubleshooting
process. The function of each LED is described in the table
below:
LED
Indicate Description
P1-P2
ON
Power supply is running normally
OFF
Power supply is disconnected or
running abnormally
RUN
ON
Device is not started or abnormal
Blinking
Blinking 1 time per second, system
is running normally
OFF
The device is powered off or the
device is abnormal.
ALM
ON
Power supply or port link has alarm
OFF
Power supply and port link have no
alarm
LINK
(G1-G12)
ON
Ethernet port has established a
valid network connection
Blinking
Ethernet port is in an active
network status
OFF
Ethernet port has not established
valid network connection
PoE
(G1-G8)
ON
POE port is powering other PD
devices normally
OFF
POE is disabled or disconnected
DI
(1-2)
ON
I/O has input information
OFF
I/O has no input information
DO
(1-2)
ON
I/O has output alarm information,
and it’s status is on.
OFF
I/O has no output alarm
information, and it’s status is off.
【
Logging in to WEB Interface
】
This device supports WEB management and configuration.
Computer can access the device via Ethernet interface. The
way of logging in to device’s configuration interface via IE
browser is shown as below:
Configure the IP addresses of computer and the
device to the same network segment, and the
network between them can be mutually accessed
Enter device’s IP address in the address bar of the
computer browser.
Enter device’s username and password in the login
window as shown below.
Click the “login” button. Change the initial password
when logging into the device for the first time, after
that, relog into the device to access the device's
Web interface.
Note:
The default IP address of the device is “192.168.1.254”.
The default user name and password of the device are
“admin”.
When logging in to the device for the first time, the
system will prompt to change the initial password of the
default user; The length of the new password string
must be greater than or equal to 8 and be composed of
two or more kinds of uppercase letters, lowercase letters,
numbers and special characters.
If the user name or password is lost, the factory settings
can be restored through the DIP switch or management
software of the device; Or make a physical loopback
between Port 1 and Port 2 within the first minute when
the switch restarts.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【
Specification
】
Panel
Gigabit PoE++ port
10/100/1000Base-T(X)
self-adaption, RJ45, Full/Half
Duplex, MDI/ MDI-X
self-adaption. The single port
supports 15.4W PoE output
power of IEEE802.3af standard
and 30W PoE+ output power of
IEEE802.3at standard, power
supply pin: 1/2-, 3/6+; 90W
PoE++ output power of
IEEE802.3bt standard, power
supply pin: 1/2-, 3/6+, 4/5-, 7/8+
Gigabit SFP slot
100/1000Base-X self-adaption
or forced mode, SFP slot
2.5G SFP slot
100/1000/2.5GBase-X
self-adaption or forced mode,
SFP slot
I/O port
Support 2 inputs and 2 outputs,
8-pin 3.81mm pitch terminal
blocks, support dry contact input
and relay-type output
Console port
CLI command management
port (RS-232), RJ45
Alarm interface
6-pin 5.08mm pitch terminal
blocks, the alarm occupies 2
pins, support 1 relay alarm
information output, the current
load capacity is 1A@30VDC or
0 3A@125VAC
Indicator
Running indicator, alarm
indicator, power supply
indicator, interface indicator,
PoE indicator, I/O output
indicator, I/O input indicator
Switch Property
Backplane bandwidth
30G
Packet buffer size
4Mbit
