manualshive.com logo in svg

3M SCOTT Vision C5, Инструкция пользователя

Поделиться
Скачать
3M SCOTT Vision C5 Скачать руководство пользователя страница 23

MAINTENANCE

P/N 595390-01

Rev D

202009

23

Maintenance

Available Parts

Removing and Installing the NoseCup Assembly

To remove the nosecup assembly

1 Reach inside the facepiece and, using only your fingers, flex the exterior surface of the nosecup from the two 

voicemitter ducts; the ducts will remain attached to the lens. See picture A in 

Figure 4-1

.

2 Grip the nosecup assembly and pull to remove it from the facepiece. See picture B in 

Figure 4-1

.

Figure 4-1   Removing the nosecup

To install the nosecup assembly

1 Insert the new or cleaned and dry nosecup assembly into the facepiece with the nosecup valves facing up. You 

must insert the nosecup behind the faceseal (inside the facepiece) away from the wearer.

2 Press the center of the nosecup tube through the hole in the front of the facepiece air deflector. It will seat in the 

air deflector hole. See Picture A in 

Figure 4-2

.

NOTE

Maintenance is limited to removing or installing the nosecup, nosecup inhalation valves, head harness, head 

harness straps, and neck strap. 

PART NUMBER  DESCRIPTION

201484-01

Nosecup assembly, Vision C5, Small

201486-01

Nosecup assembly, Vision C5, Medium

201488-01

Nosecup assembly, Vision C5, Large 

31002788 

Valve, inhalation, red

201495-03

Kevlar head net, Vision C5, Small

201495-02 

Kevlar head net, Vision C5, Medium

201495-01

Kevlar head net, Vision C5, Large

804178-05

Kevlar upper strap, head harness, Vision C5

804178-03 

Kevlar lower strap, head harness, Vision C5

201682-01

Neck Strap, Vision C5

Table 4-1   Available parts for the 3M Scott Vision C5 Facepiece

A

B

Содержание SCOTT Vision C5





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды