background image

CLEANING & STORING THE RESPIRATOR

48

P/N 595360-01

Rev G

202004

Machine Washing the Shoulder Harness and Waist Pad

Machine wash the shoulder harness, waist pad, and straps to remove dirt and stains.

Clean your 3M Scott Air-Pak X3 Pro soft goods at least 

once every year

.

Place all soft goods in a mesh bag (P/N 31004024) before machine washing.

Use a 

front-loading

 extractor or commercial washing machine with tumbling action to reduce potential 

mechanical damage to the soft goods. If the machine has an adjustable drum RPM, set it so the 

g-force does not 

exceed 100g

. Refer to the manufacturer’s instructions for details.

To machine wash the shoulder harness and waist pad

1 Detach the shoulder harness, waist pad, straps, and UEBSS or dual EBSS pouch (if installed) from the backframe 

as outlined in 

Chapter 2: Soft Goods Assembly & Disassembly

” on page 25.

2 Perform a visual inspection for soiling, contamination, physical damage, or thermal damage. See “

Performing a 

General Inspection

” on page 12 in 

Chapter 1: Inspecting the Respirator

.

3 If necessary, spot treat any heavily soiled areas. See 

Spot Cleaning the Shoulder Harness and Waist Pad

” on 

page 47.

4 Close 

all

 fasteners (snaps and buckles) on the shoulder harness and waist pad assemblies, paying special 

attention the following:

Remove the regulator holder from the waist belt.
– Carefully pull the waist belt (on the side with the female buckle component) through the openings of the 

regulator holder. 

– Set the regulator holder aside.

Buckle the male and female ends of the waist belt.

Attach the waist pad retaining strap to the waist pad. Be sure to thread both ends through the sewn loops on 

the waist pad and snap them in place on the waist pad. 

If you have a UEBSS or dual EBSS pouch, be sure to remove the UEBSS or dual EBSS hose and close all 

fasteners on the pouch. 

5 Place the soft goods in the mesh bag. Tighten the bag’s drawstrings and load the bag into the washing machine. 

Do not overload the machine

.

6 Follow the washing machine manufacturer’s instructions for adding laundry detergent, setting the water level and 

temperature, adjusting the drum RPM, and starting a normal wash cycle.

CAUTION

If your equipment was exposed to contaminants but is suitable for reuse according to your organization’s 

assessment procedure:

Wash the equipment separately from other equipment in a dedicated commercial washing machine. 

Avoid using home or public machines to prevent spread of the contaminants.

CAUTION

Avoid using a top-loading washing machine as the agitators in such machines can damage the material and 

seams of soft goods.

Содержание SCOTT AIR-PAK X3 PRO

























































Отзывы: