background image

CLEANING & STORING THE RESPIRATOR

46

P/N 595360-01

Rev G

202004

To perform a regulator check

1 Make sure the respirator cylinder is at least 1/2 full to prevent the Vibralert from initiating and obscuring the 

sound of air flowing from the regulator.

2 Verify that the air saver/donning switch is depressed on the E-Z Flo+ regulator or the auto air-saver switch is 

engaged on the E-Z Flo C5 regulator latch.

3 Close the purge knob.
4 Reattach the regulator to the respirator (if removed for cleaning). 
5 Slowly open the cylinder valve at least 1 full turn. 
6 If you hear air flowing from the regulator, close the cylinder valve and repeat steps 2 through 5. If you still hear air 

flow, close the cylinder valve fully, tag the unit for repair, and remove it from service. 

7 Open the purge valve and observe the air flow from the regulator spray bar. Droplets of water indicate the 

regulator is not dry. Dry the regulator according to step 8 of “

To clean the mask-mounted regulator

” on page 44 

and repeat the regulator check.

NOTE

The regulator check is not intended to be a complete functional check of the respirator. Before your next 

use of the respirator, perform a regular operational inspection as described in “

Chapter 1: Inspecting the 

Respirator

” on page 11.

NOTE

If the cylinder is 1/3 full or less, the Vibralert will initiate. If the Vibralert does not initiate, tag the unit for 

repair and remove it from service.

Содержание SCOTT AIR-PAK X3 PRO

























































Отзывы: