3M Litmann Quality 3100 Скачать руководство пользователя

Страница: 5 / 16

78-8127-6830-3-C

3.4

If cable includes a ground check, the ground check connector should be

wrapped with one half-lapped layer of 3M

™

Temflex

™

Electrical Vinyl Tape

1700P extending ¼" (6 mm) onto existing insulation, followed by a half-lapped

layer (

tacky side DOWN

) of Scotch

Linerless Rubber Splicing Tape 130C

extending ¼" (6 mm) past the 1700P tape, then using the same ¼" (6 mm)

overlap, add a final layer of half-lapped 1700P tape.

3.5

Connect remaining ground wires.

Figure 8

4.0 Replace Jacket

4.1

Start 1" (25 mm) above split or top of taper and apply half-lapped layers of

130C tape (

tacky side DOWN

) across splice and 1" (25 mm) past end of

opposite split or top of taper. Apply half-lapped layers, filling all voids until

splice area is returned to greater than or equal to original cable profile.

1" (25 mm)
past split or
top of taper

Scotch

Linerless

Rubber Splicing Tape 130C

Tacky Side DOWN

Figure 9

4.2

Start 2" (50 mm) from 130C tape and apply one half-lapped layer of Scotch

Heavy Duty Mining Tape 31 with mastic side toward the cable across the splice

and continue 2" (50 mm) past the end of the Scotch

Linerless Rubber Splicing

Tape 130C. Always wrap the 31 tape toward the machine end of the cable.

2" (50 mm)
past end of
previous layer

Scotch

Heavy Duty Mining Tape 31

(Mastic side toward cable)

Machine End

Start taping here

Figure 10

Содержание Litmann Quality 3100

















Результаты поиска

Содержание Litmann Quality 3100

Отзывы:

Похожие инструкции для Litmann Quality 3100

Бренды по названию

Популярные бренды

3M Litmann Quality 3100, Инструкция по эксплуатации

Результаты поиска

Содержание Litmann Quality 3100

Отзывы:

Похожие инструкции для Litmann Quality 3100

Бренды по названию

Популярные бренды