3M Litmann Quality 3100 Скачать руководство пользователя

Страница: 1 / 16

™

Mining Cable Splice Kit 3100

Instructions

Kit Contents:

1 Scotch

Heavy Duty Mining Tape 31, 2" x 8.5'

1 Scotch

Linerless Rubber Splicing Tape 130C, 1½" x 30'

1 3M

™

Temflex

™

Vinyl Electrical Tape 1700P, 1½" x 44'

1 3M

™

Cable Cleaning Preparation Kit CC-2-Dry

1 Instruction Sheet

Note: Scotch

Linerless Rubber Splicing Tape 130C is applied highly-stretched with

tacky side DOWN.

Technical Information:

For use on 2, 3 or 4-Conductor Flat Type W, G or G-GC

3 or 4-Conductor Round Type W, G or G-GC

#6 AWG–1/0 AWG (14-50 mm

)

600 V–2 kV
Cables up tp 500 kcmil (250 mm

) will require the use of additional tapes.

Mine Safety and Health Administration Acceptance:

P-07-KA080005/00-MSHA

DANGER

Before attempting any cable repairs, make sure that the proper cable is

disconnected, locked out and suitably tagged.

CAUTION

Working around energized systems may cause serious injury or death. Installation

should be performed by personnel familiar with good safety practice in handling

electrical equipment. De-energize and ground all electrical systems before installing

product.

August 2009
78-8127-6830-3-C



Содержание Litmann Quality 3100

















Результаты поиска

Содержание Litmann Quality 3100

Отзывы:

Похожие инструкции для Litmann Quality 3100

Бренды по названию

Популярные бренды

3M Litmann Quality 3100, Инструкция по эксплуатации

Результаты поиска

Содержание Litmann Quality 3100

Отзывы:

Похожие инструкции для Litmann Quality 3100

Бренды по названию

Популярные бренды