3M Filtrete 3M-10 Скачать руководство пользователя страница 5

PG

 7

PG

 8

Please refer back to these guidelines for safe and secure wire 
connections.
•Take care 

not to damage the labels

 for each wire in handling.

•Strip insulation 3/8 in. (9.5mm) from wire ends. 
•Connect labeled wires only to a terminal with corresponding letter.
•Bend the wire slightly, insert the wire under the contact plate and 
tighten the screw down onto the wire.

The Wire Label List shows wire 
labels used on thermostats. 
Please determine what wires you 
have and select the correct wiring 
diagram to "go to" on pages 8-9.
If you have a 

HEAT PUMP

 select a 

wiring diagram on pg 9.

Before you Connect Wires

Caution

D o   n o t   a l l o w  
w i r e s   t o   t o u c h  

e a c h   o t h e r   o r   p a r t s   o n   u n i t .  
Wi r e s   m u s t   b e   r o u t e d   t h r o u g h  
t h e   h o l e   i n   t h e   b a c k   p l a t e ,   b e l o w  
t h e   t e r m i n a l   b l o c k ,   o r   t h e y   w i l l  
h i t   p a r t s   o n   t h e   c o v e r.

 Make sure your wires are labeled

.  This is necessary to determine which step-by-step 

wiring diagram you should use. This may require you to find the 'other end' connection for 
each wire on your heating or air conditioning equipment and read the label there. 
     If you have a Zoned Heating/Cooling system with multiple thermostats, please refer to 
our website at www.radiothermostat.com/filtrete for installation notes or call 1-888-607-5824

Wire Connections 

What Wires Do You Have?

Go To Page 13

Go To Page 14

WIRE LABEL LIST

R

 - Single source power for heat/cool 

(R connected to 

RC and RH using the jumper wire)

RH or R

 - Heating Power

RC

 - Cooling Power

W

 - Heating return 

G

   - Fan return

Y

   - Compressor return

H

  - Humidifier 

(built into the furnace)

W2

 - 2nd stage heat in NORMAL, auxiliary heat in PUMP mode.

A

  - For 3 wire zoned heating systems 

C

  - AC power for the thermostat if available

O

  -  Damper control 

(Zoned heating)

 or heat pump 

changeover valve (powered in COOL)

B

  - Damper control

 (Zoned heating)

 or heat pump 

changeover valve (powered in HEAT)

NOTE: Do 

not connect both O and B on a heat pump. Connect O 
to O & tape off B.

X  - Tape off X
E  - Tape off E

Go To Page 11

Go To Page 12

Содержание Filtrete 3M-10











Отзывы: