3M CTM051 Скачать руководство пользователя страница 13

Страница: 13 / 16

Specifications

Impedance

Range

0.001 – 1.999 Ohms

Automatic auto-zero for test leads

EMI (noise on ground)

Bandwidth

9kHz – 450MHz

Measurement Range

80 dBuV – 140 dBuV

10 mV – 10 RMS

Measurement Type

Average

Envelope Peak

Voltage on Ground

AC (50 – 500 Hz)

0.001 – 270 V RMS

0.001 – 400 V

Reference

Individual reference setting for each parameter

Hold

Hold, Hold Max

General

Power

Battery 9V Alkaline

Dimensions (approx.)

4.5” x 3.6” x 1.1”

114 mm x 92 mm x 28 mm

All specifications are subject to change without notice.

is active. Please note that if you power down the 3M

™

Ground Pro Ground Integrity

Meter while in any of these modes, it will remain in the same mode when the unit is
powered up again.

Pressing the Hold button one more time puts the Ground Pro back into regular mode.

Содержание CTM051

















Результаты поиска

Содержание CTM051

Отзывы:

Похожие инструкции для CTM051

Бренды по названию

Популярные бренды

3M CTM051, Руководство пользователя

Результаты поиска

Содержание CTM051

Отзывы:

Похожие инструкции для CTM051

Бренды по названию

Популярные бренды