3M 9200IC Plus Скачать руководство пользователя страница 31

Страница: 31 / 56

™

Digital Wall Display

Menu System

Configuration

Auto Switch Input

Switches the display to the next available input.

Auto Switch PIP

Switches the audio to the next available input.

Auto Shutoff

Turns the unit off at a defined time

Blank Color

Changes the color of the displayed image when the blank button is pushed.

Splash Screen

Use to change the start up screen or the No Input Detect Screen

DVI EDID Select

Select DVI to Digital for a digital source or select DVI to analog for an analog source.

Reset System to
Defaults

Resets all menu functions to the default setting.

Information

Displays the following maintenance and servicing information.

• Lamp Hours: The total time on the lamp

• Optical Engine Hours: Total time on the optical engine

• System Hours: Total time power has been applied to the 3M Digital Wall Display.

• Software Version Number: The version of software on the Display Controller Board

• Software Build Number: The build number for the software that is on the Display

Controller Board.

• DCB Serial Number:Shows the serial number for the 3M Digtital Wall Display.

• Arm Software Module: Shows the software version for the arm module

• I-Port Software Version: Shows the eBeam

™

Imageport software version.

• IP Address: This displays the IP address for networking via the Ethernet connection.

• MAC Address: Displays the MAC address for the 3M Digital Wall Display.

• Pod Software Version: Displays the eBeam pod software version for the product.

On Screen Timer

Selects a time period to count down on the display

Network

Configure the network setting for the unit

• DHCP: Turn DHCP on/off

• IP Address: Set the IP address

• MAC: Display the MAC address

• Gateway: Set the Gateway for the network

• Subnet Mask: Set the Subnet Mask for the network

Diagnostics

Diagnostics is used only by an authorized service person.

Language

Select the OSD language

Содержание 9200IC Plus

























































Результаты поиска

Содержание 9200IC Plus

Отзывы:

3M 9200IC Plus, Руководство оператора, Страница: 31 / 56

Результаты поиска

Содержание 9200IC Plus

Отзывы: