manualshive.com logo in svg

3M 3M-Matic S-857, Инструкция и перечень запасных частей

Поделиться
Скачать
3M 3M-Matic S-857 Скачать руководство пользователя страница 18

15

Tape Loading and Threading

 – The tape drum assembly is set up for dispensing 3/8 inch [9 mm] or 1/2 inch

[12 mm] wide tape.  For dispensing other tape widths refer to "Adjustments – Tape Width", page 17.  A tape
threading diagram is located outside the applicator on the top of the nest for quick reference.

WARNING – Turn "Off" main air supply at on/off valve before threading tape.  Failure to turn
air supply "Off" could result in severe personal injury or equipment damage.

For easy access to tape loading and threading, open
the cover located on the right side of the S-857.
Release the cover latch, shown in Figure 2-1, pull
outward on the upper part of the latch, unhook the
latch and pivot open the cover.

Operation

Refer to Figure 4-1 and thread the tape as follows:

1.

Place the tape roll on the tape drum so the tape
is dispensed downward, adhesive side forward.
The tape roll must be fully against the drum
flange.

2.

Pull approximately 12 inches [300 mm] of tape
from the roll and thread the tape under the
tension roller, adhesive side up.

Figure 4-1 – Tape Loading and Threading – Right Side View

Содержание 3M-Matic S-857














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды