3M 10500 страница 20 Скачать руководство пользователя

Страница: 20 / 50

NA - ENG

April 2017

3M-Matic

™

Accuglide 2+ - 3 Inch Taping Head

Page 12

(Maintenance

continued

on next page.)

Figure 4-1 Blade Replacement

Knife

Guard

Knife

Holder

Maintenance

The AccuGlide™ 2+ Standard 3 inch

Taping Head has been designed for

long, trouble free service. The taping

head will perform best when it

receives routine maintenance and

cleaning. Taping head components

that fail or wear excessively should

be promptly repaired or replaced to

prevent damage to other portions of

the head or to the product.

Blade Replacement

, Upper and Lower

Taping Heads –

Figure 4-1

1. Loosen, but do not remove, the

blade screws (A). Remove and

discard old blade.

2. Mount the new blade (B) with the

beveled side away from the blade

holder.

3. Bottom the blade slots against

the screws (this will position the

blade at the correct angle.)

Tighten the blade screws to

secure

the

blade.

Note

–

Check the blade position

to insure proper clearance

between blade and guard by

slowly pivoting blade guard back.

Blade Guard

The blade guard covers the blade

whenever a box is not being taped.

Periodically check to be sure the

blade guard is functioning properly

and returning to cover the blade.

Replace any defective parts.

Blade Oiler Pad

To reduce adhesive build-up, the

taping heads are equipped with

a factory pre-lubricated felt oiler

pad that provides a

lm of oil on

the cutting edge of the blade.

Blade maintainance should include

keeping the felt oiler pad saturated

with

Silicone.

Should tape adhesive build-up

occur on blade, carefully wipe

clean with an oily cloth.

• To reduce the risk associated with

sharp blade hazards:

- Keep hands and

ngers away from

tape cuto

blades under orange blade

guards. The blades are extremely sharp.

WARNING

• To reduce the risk associated with

shear, pinch, and entanglement hazards

- Turn air and electrical supplies o

on associated equipment before

  performing any adjustments, mainte-
  nance, or servicing the taping heads
-  Never attempt to work on the taping

head or load tape while the box drive

system is running

WARNING

Содержание 10500



















































Результаты поиска

Содержание 10500

Отзывы:

Похожие инструкции для 10500

Бренды по названию

Популярные бренды

3M 10500, Инструкция и перечень запасных частей

Результаты поиска

Содержание 10500

Отзывы:

Похожие инструкции для 10500

Бренды по названию

Популярные бренды