3D Systems projet mjp 2500 Скачать руководство пользователя

Страница: 25 / 92

Press the release button (C) on the front. You will hear the cartridge release. Pull the cartridge out of the slot.

Dispose of the empty cartridge according to local regulations.

Wearing nitrile gloves and either protective sleeves or a lab coat to protect arms, use a disposable paper towel and wipe all material from the container seal

assembly, if necessary you can use some isopropyl alcohol on the paper towel to wipe up the excess material.

NOTE: It is important to always wear nitrile gloves and either protective sleeves or a labcoat to protect arms when coming in contact

with materials to avoid getting materials on skin. Contact with skin may cause an allergic reaction.

Installing New Material Cartridge

NOTE: Cartridges cannot be installed into a cold printer. The printer must be warm before drawer will open and cartridges can be

installed.

To place a material cartridge into the MDM, perform the following steps:

Obtain a new material cartridge ensuring that it is the same material as currently installed in the MDM.

Содержание projet mjp 2500





























































































Результаты поиска

Содержание projet mjp 2500

Отзывы:

Похожие инструкции для projet mjp 2500

Бренды по названию

Популярные бренды

3D Systems projet mjp 2500, Руководство пользователя

Результаты поиска

Содержание projet mjp 2500

Отзывы:

Похожие инструкции для projet mjp 2500

Бренды по названию

Популярные бренды