3D Systems ProJet 4500 Скачать руководство пользователя

Страница: 40 / 44

3D Systems, Inc.

INSTALL SOFTWARE

If 3DPrint® has not been installed, you will first need to install it. Installation instructions are available in the 3DPrint Software User

Manual. Be sure to install the software on the same computer that is connected to your 3D Printer. Also be sure you use the version of

3DPrint® that came with your ProJet® 4500 system.

If you encounter any problems during installation, please contact your local Service Provider or Reseller, or visit the Support section of

our Web site at

3dscentral.3dsystems.com.

Please refer to 3DPrint® Software User Manual for further information.

IMPORTANT:

To avoid problems that may occur during printing, ensure that all screen savers and your power management software is

turned off on the computer driving your 3D printer. Most screen savers and power management software can be turned off in the main

Windows screen settings. For additional instructions on how to disable your hardware and software power management, please consult

your computer’s hardware Owner’s Manual.

NOTE:

You must have Administrator rights to install 3DPrint® correctly.

If you encounter any problems during the 3DPrint® installation, please contact your local Reseller, or visit the support section of our Web
site: 3dscentral.3dsystems.com

Go to your Host/PC where 3DPrint will be running on, and perform the following steps:

1. Close all running applications and insert the 3DPrint installation me-

dia (a USB tumb drive) into your computer.

2. If the Installer does not automatically start, double-click on your Drive

icon. Double-click on the Setup.exe icon. This starts the 3DPrint

installation.

Содержание ProJet 4500












































Результаты поиска

Содержание ProJet 4500

Отзывы:

Похожие инструкции для ProJet 4500

Бренды по названию

Популярные бренды

3D Systems ProJet 4500, Руководство по установке

Результаты поиска

Содержание ProJet 4500

Отзывы:

Похожие инструкции для ProJet 4500

Бренды по названию

Популярные бренды