manualshive.com logo in svg

3D Hobby Shop 49 Sukhoi 26MX, Инструкция по сборке

Поделиться
Скачать
3D Hobby Shop 49 Sukhoi 26MX Скачать руководство пользователя страница 2

 

2

 

Developer’s Note 

 

 

 

 

 

 

As a full-size Sukhoi pilot, one of my dreams has always been to see my airplane, N25SU, in 
model form. That dream got a little closer to reality when I started doing model development for 
3D Hobby Shop in 2006. At some point in late 2007, both Ben and I made a commitment to 
model the Sukhoi. Setting our sights rather high, we aimed to design what would be the premier 
Sukhoi model on the market, incorporating not only outstanding flying characteristics, but also 
many of the scale features rarely seen on Sukhoi models. We were able to accomplish both of 
those goals, and much more. I am proud to introduce the 3D Hobby Shop Sukhoi 26 in two 
distinct sizes – 49” and 57”. 
For me, the Sukhoi represents the ultimate aerobatic experience. Its combination of beautiful 
sculpted lines and aggressive stance make it one of the most distinct airplanes on the competition 
circuit. Designed in the mid 80’s, the Sukhoi 26 was created for one purpose, and one purpose 
alone – to dominate world aerobatic competition. Dominate it has, amassing more Gold 
International medals than all other designs combined. We wanted to design a model that captured 
that aggressive precision attitude, while combining it with unlimited 3D/freestyle performance. 
The 3DH Sukhoi’s clean lines allow great tracking, while the thin 10% airfoil allows great pitch 
performance and fast cruising speeds. Oversized control surfaces make the Sukhoi one of the 
most responsive 3D airplanes on the market. The roll rate, in particular, can be absolutely 
blinding. Unlike the full size Sukhoi, the 3DH version has only light coupling in KE flight, and 
only very light wing rock upright, none inverted. Typical of all 3DH airplanes, the Sukhoi 
incorporates all of the high end accessories you’ve come to expect including a carbon wing tube, 
carbon landing gear, tool-free wing attachment, slotted self-aligning wheel pants, and a complete 
hardware pack. In all, I feel the 3D Hobby Shop SU-26 is the ultimate Sukhoi RC model airplane 
available today.  

-

Scott Stoops 

3D HOBBY SHOP 

 

Содержание 49 Sukhoi 26MX































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды