3D Foamy 3DF016 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 23

background image

Page

© 2004 3D Foamy (Levi Jordan) All Rights Reserved.

1

F-18 Park Jet

Made In Washington State, USA!

Kit# 3DF016

A High Performance Electric Jet

About This Construction Manual

This booklet divides the construction into sub-assemblies; wing, fuselage, etc.

Please read each section carefully before starting

on that particular sub-assembly.

There is a complete description of all parts under “Kit Contents” Please check to make sure your kit

is complete. We are human, and occasionally miss something! If you have trouble identifying a part, or are missing something, please
contact us and we can help.

During the construction process the steps will outline what part to use. We have used actual pictures instead of unclear or often
inaccurate illustrations to assist in the building process. This manual was intended for English users, and all measurements are made in
standard units. (Inch, foot, etc.)

Customer Service:

Should you experience a problem building or flying this kit, we recommend you see your hobby shop first. If you are unable to solve
the problem, feel free to write:

3D Foamy (Levi Jordan)

10040 West Barberry

Cheney, WA 99004

[email protected]

or online at

www.3DFoamy.com

This product is sold with exclusion of all warrantee, expressed or implied, statutory or otherwise.

Pilot assumes all risk in building and operating this model. Do not operate if you are not an experienced modeler. Refer to

and abide by AMA rules at

www.modelaviation.com

for regulations on Radio Control Models.

1
2
3
...
»

Содержание 3DF016
























Отзывы:

Нет отзывов

Похожие инструкции для 3DF016

Бренд: M.T.H. Страницы: 2

F/A-18E interior S.A.

Бренд: Eduard Страницы: 4

Бренд: iKarus Страницы: 15

Бренд: roco Страницы: 8

Techno Tiles TT Castle

Бренд: The Learning Journey Страницы: 386

Бренд: Magnetic Racing Страницы: 43

MINI SKY HUNTER

Бренд: H-KING Страницы: 8

Gatekeeper's lodge 282738

Бренд: Faller Страницы: 4

Бренд: VTech Страницы: 19

SAMMIE & BERTIE

Бренд: roundhouse Страницы: 20

Verkehrsschranke Grand

Бренд: Jamara Страницы: 4

Бренд: Stevens AeroModel Страницы: 29

Бренд: H-KING Страницы: 13

Бренд: PARKZONE Страницы: 10

Ninjago Masters of Spinjitzu Wyplash 4645006

Бренд: LEGO Страницы: 2

Бренд: PCM Страницы: 13

AQUA STAR HRR502

Бренд: Herr Engineering Страницы: 9

Бренд: Ripmax Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды