manualshive.com logo in svg

3Com VCX V7000, Руководство по обслуживанию

Поделиться
Скачать
3Com VCX V7000 Скачать руководство пользователя страница 136

136

C

HAPTER

 8: M

ANAGING

 U

NINTERRUPTIBLE

 P

OWER

 S

UPPLIES

The optional argument 

--fullauto

 specifies that the command should 

run in automatic mode. In this mode, command execution does not 
provide any interactive prompts or queries.

Note that you can enter the 

vcx-ups-setup 

command with the optional 

--help 

argument to display information on command usage.

Monitoring UPS 
Status

This section describes how to check the status of a UPS

You can use the 

vcx-ups-status

 command to check the status of any 

UPS in your local VCX system, or the status of a UPS in a remote VCX 
system. You can enter the command on the master server or any slave 
server. The 

vcx-ups-status

 command uses the following syntax:

vcx-ups-status (ups0 | ups1)[master-ip] [--parameter]

You must identify the UPS you want to monitor. For a single UPS system, 
enter 

ups0

. For a dual UPS system, enter either 

ups0

 or 

ups1

, depending 

on the UPS you want to monitor.

The parameter 

master-ip

 is optional. Use this parameter to specify the IP 

address of a remote VCX UPS master server.

In addition to the required parameter 

ups0

 or 

ups1

, you must enter one 

of the parameters shown in 

Table 10

.

Table 10   

vcx-ups-status Command Parameters

Parameter

Description

--upsstatus

Indicates the status of the UPS, for example 

online

 or 

offline

.

--upsload

Indicates the load, expressed in watts, placed on the UPS by 
the attached VCX servers.

--upsmfr

Displays the name of the UPS manufacturer. In this case, the 
value is always 

APC

.

--batterycharge

Indicates, as a percentage, the current battery charge.

--upsserial

Displays the manufacturer’s serial number of the UPS.

--upsmodel

Displays the manufacturer’s model name of the UPS.

--isconfig

Indicates whether or not (

Y

 or 

N

) the UPS has been 

configured.

Содержание VCX V7000

























































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды