3Com Switch 7700 Скачать руководство пользователя страница 14

Страница: 14 / 59

S W I T C H 7 7 0 0 C O M P O N E N T S

Table 9 Description of fan LED

Indicator State

description

Green — the fan works normally.
Off — the fan fails to work or has not been installed.

FAIL

Green — the fan fails to work.

Off — the fan works normally or has not been installed.

3.1.6. Switching I/O Modules

The Switch 7700 provides 6 I/O modules slots below the Fabric (FAB64) slot. (See Figure 2-1). The Switch 7700
supports the following I/O modules:

8-port 1000BASEX

(GBIC) GE module

(8GBIC) (3C16858)

8-port 10/100/1000BASE-T GE module

(8BT) (3C16859)

24-port 100BASE-FX MMF

FE module

(24FX) (3C16861)

48-port 10/100BASE-T auto-sensing FE module

(48T) (3C16860)

Consider the following when selecting I/O modules:

You can configure several I/O modules of the same type

All 6 I/O module slots are the same and any combination of I/O modules can be
inserted

You should select I/O module port cables that are compatible with each installed I/O
module

48-port 10/100BASE-T Auto-sensing FE Card (48T) (3C16860)

The 48T module provides 48 external 100Mbps Ethernet electrical ports and is illustrated in Figure 4.

Figure 4 The 48-port 10/100BASE-T Auto-sensing FE Card

Table 10 describes the attributes of the 48TX module.

Table 10 Attributes of the 48-port 10/100BASE-T Auto-sensing FE Card

Attribute 48TX

CPU MPC850
BootROM 512KB
SDRAM 64MB
Dimensions

(

L X W)

366.7mm x 340mm

Maximum power consumption

55W

Connector RJ-45
Quantity of port(s)

Содержание Switch 7700




























































Результаты поиска

Содержание Switch 7700

Отзывы:

Похожие инструкции для Switch 7700

Бренды по названию

Популярные бренды

3Com Switch 7700, Руководство по установке

Результаты поиска

Содержание Switch 7700

Отзывы:

Похожие инструкции для Switch 7700

Бренды по названию

Популярные бренды