manualshive.com logo in svg

3Com SuperStack II Switch 1100, Быстрое руководство по установке, Страница: 2 / 6

Поделиться
Скачать
3Com SuperStack II Switch 1100 Скачать руководство пользователя страница 2

2

C

HAPTER

 : Q

UICK

 I

NSTALLATION

 G

UIDE

 

FOR

 

THE

 S

UPER

S

TACK

 II S

WITCH

 1100/3300 ATM E

XPANSION

 M

ODULE

Warning

: 

Disconnect the Switch from

 

the network, 

power it off and then disconnect the Switch from the 
main power supply.

Step 1:

Remove the blank plate that is located at the back of 
the SuperStack II Switch, by unscrewing the two Phil-
lips screws as shown in 

Figure 1

. 

Retain the blank plate and the screws for future use.

Figure 1   

Removing the Blank Plate

Step 2:

Hold the module with the cutout on your front left 
side,without touching the top or bottom of the circuit 
board. Use the guide rails within the switch slot to 
align the ATM Expansion Module as shown in 

Figure 2

.

Slide the ATM Expansion Module into the slot. Ensure 
that the module is fully engaged to the switch. You 
should hear a click.

Figure 2   

Aligning and Inserting the ATM Expansion Module

Blank Plate

Cutout

Содержание SuperStack II Switch 1100







Отзывы:

Нет отзывов