3Com SuperStack 3 3C17300A Скачать руководство пользователя страница 58

Страница: 58 / 84

PPENDIX

A: S

AFETY

NFORMATION

Important Safety Information

WARNING:

Installation and removal of the unit must be carried out by

qualified personnel only.

WARNING:

If installing the Switch 4200 Family unit in a stack with

SuperStack II or SuperStack 3 units that are shallower than the 4200
Family, the Switch 4200 Family unit must be installed below the narrower
units.

WARNING:

The unit must be earthed (grounded).

WARNING:

Connect the unit to an earthed power supply to ensure

compliance with safety standards.

WARNING:

Power Cord Set:

This must be approved for the country where it is used:

WARNING:

The appliance coupler (the connector to the unit and not the

wall plug) must have a configuration for mating with an EN60320/IEC320
appliance inlet.

U.S.A. and
Canada

■

The cord set must be UL-approved and CSA certified.

■

The minimum specification for the flexible cord is:

No. 18 AWG

Type SV or SJ

3-conductor

■

The cord set must have a rated current capacity of at least
10A.

■

The attachment plug must be an earth-grounding type
with a NEMA 5-15P (15A, 125V) or NEMA 6-15P (15A,
250V) configuration.

United
Kingdom only

■

The supply plug must comply with BS1363 (3-pin 13 amp)
and be fitted with a 5A fuse which complies with BS1362.

■

The mains cord must be <HAR> or <BASEC> marked and
be of type H03VVF3GO.75 (minimum).

Europe only:

■

The supply plug must comply with CEE 7/7 (“SCHUKO”).

■

The mains cord must be <HAR> or <BASEC> marked and
be of type H03VVF3GO.75 (minimum).

Denmark

■

The supply plug must comply with section 107-2-D1,
standard DK2-1a or DK2-5a.

Switzerland

■

The supply plug must comply with SEV/ASE 1011.

DUA1730-0AAA03.book Page 58 Thursday, November 17, 2005 12:17 PM

Содержание SuperStack 3 3C17300A





















































































Результаты поиска

Содержание SuperStack 3 3C17300A

Отзывы:

Похожие инструкции для SuperStack 3 3C17300A

Бренды по названию

Популярные бренды

3Com SuperStack 3 3C17300A, Руководство по началу работы

Результаты поиска

Содержание SuperStack 3 3C17300A

Отзывы:

Похожие инструкции для SuperStack 3 3C17300A

Бренды по названию

Популярные бренды