3Com Router 3000 Series Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 37

3Com Router 3000 Series Скачать руководство пользователя страница 34

Faceplate and LEDs

Figure 20 illustrates the faceplate of the

1-port channelized E3

module.

Figure 20

Faceplate of the 1-Port Channelized E3 Module

The following table lists the meanings of the LEDs on the faceplate.

Cables

The external interface provided by a 1-port channelized E3 module is two SMB
sockets respectively for Tx (Transmitter end) and Rx (Receiver end). The interface
uses the 75ohm unbalanced transmission mode and uses a pair of 75ohm
unbalanced coaxial cables to connect the peer device.

Figure 21

E3/T3 cable

Note:

1) The 1-port channelized E3 and 1-port channelized T3 modules use the same E3/
T3 cable.

Supported network protocol

IP

IPX

Protocols supported

X.25

Frame Relay

PPP

MP

HDLC

LAPB

Table 23

Features of the 1-Port Channelized E3 Module (continued)

Attribute

Description

Table 24

1-Port Channelized E3 Module LEDs

LED

Meaning

LINK

OFF: The link is not set up.

ON: The link has been set up.

ACT

OFF: No data is being transmitted or received.

Flashing green: Data is being transmitted and received.

BNC connector

SMB connector

3Com Router Release Notes for V1.20

34

«
...
32
33
34
35
36
...
»

Содержание Router 3000 Series






































Отзывы:

Нет отзывов