3Com 3CR17450-91 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 86

background image

Placing Units On Top of Each Other

23

Achtung:

Entfernen Sie alle Kabel, bevor Sie fortfahren. Entfernen Sie die

selbstklebenden Polster (Füße) von der Unterseite der Baugruppe, falls
diese bereits angebracht sind.

Achtung:

Wenn Sie einen Einbaurahmen oder Schrank benutzen, stellen

Sie sicher, dass der Luftstrom durch die Seitenflaechen des Switches nicht
beeintraechtigt wird.

Um den Switch einzubauen:

1

Stellen Sie den Switch mit der rechten Seite nach oben und der Frontseite
zu Ihnen auf eine flache Oberflaeche.

2

Legen Sie die Montagewinkel ueber die Montageloecher auf der Seite
des Geraetes, wie in Figur 4 gezeigt.

3

Fuehren Sie die vier mitgelieferten Schrauben in den Winkel ein und
ziehen Sie sie mit einem Schraubendreher gut fest.

4

Widerholen Sie letzten beiden Schritte auf der anderen Seite der
Baugruppe.

5

Stecken Sie den Switch in den 19" Schrank und sichern Sie ihn mit
passenden Schrauben (nicht mitgeliefert) Stellen Sie sicher, dass die
Ventilationsoeffnungen nicht verdeckt sind.

6

Schließen Sie alle Kabel wieder an.

Placing Units On
Top of Each Other

If the Switch units are free-standing, up to four units can be placed one
on top of the other. If you are mixing a variety of Switch and hub units,
the smaller units must be positioned at the top.

If you are placing Switch units one on top of the other, you must use the
self-adhesive rubber pads supplied. Apply the pads to the underside of
each Switch, sticking one in the marked area at each corner. Place the
Switch units on top of each other.

Supplying Power to
the Switch

Power problems can be the cause of serious failures and downtime in
your network. Ensure that the power input to your system is clean and
free from sags and surges to avoid unforeseen network outages. 3Com
recommends that you install power conditioning, especially in areas
prone to black outs, power dips and electrical storms.

«
...
23
24
25
26
27
...
»

Содержание 3CR17450-91























































































Отзывы:

Нет отзывов

Похожие инструкции для 3CR17450-91

Бренд: Cabletron Systems Страницы: 88

SmartSwitch 9A100

Бренд: Cabletron Systems Страницы: 52

SmartSwitch 9W006

Бренд: Cabletron Systems Страницы: 34

SmartSTACK ELS100-S24TX2M

Бренд: Cabletron Systems Страницы: 102

Бренд: Cabletron Systems Страницы: 24

SmartSwitch 9000

Бренд: Cabletron Systems Страницы: 14

Бренд: Cabletron Systems Страницы: 38

Бренд: Waters Network Systems Страницы: 16

Бренд: A-Neuvideo Страницы: 16

Бренд: Black Box Страницы: 9

VH M 1 1 1 Series

Бренд: Jlso Tec Trade Страницы: 15

Бренд: HDTV Supply Страницы: 15

Бренд: Advantech Страницы: 101

Бренд: LevelOne Страницы: 76

Бренд: Phonic Страницы: 16

Бренд: J-Tech Digital Страницы: 13

Бренд: SolidView Страницы: 39

Бренд: Lanpro Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды