manualshive.com logo in svg

3Com 3Com SuperStack 3 Switch 3800 Family, Руководство пользователя

Поделиться
Скачать
3Com 3Com SuperStack 3 Switch 3800 Family Скачать руководство пользователя страница 28

1-10

C

HAPTER

 1: S

WITCH

 3800 O

VERVIEW

MAC Address

This label shows the unique Ethernet MAC address assigned to this 
device.

Console Port

The console port (9-pin, “D” type connector) is used to connect a 
terminal and to carry out local out-of-band management. 

Factory Defaults

Table 1-3 shows the factory defaults for the Switch 3800 features.

Table 1-3   

Switch 3800 Factory Defaults

Item

Default Setting

Port status

Enabled on all ports

Default user account

admin

 with no password and 

user

 with no 

password

Console port configuration

9600 baud, eight data bits, one stop bit, no 
parity, XON/XOFF flow control enabled

SNMP read community string

Public

SNMP write community string

Private

RMON history session

Enabled

RMON alarms

Enabled

■

Send trap if load is greater than 75% of 
available bandwidth

■

Send trap if there are more than 10 errors in 
1,000 packets

PACE

Recognition disabled

Virtual LANs

One VLAN named 

default

; all ports belong to the 

default VLAN; no protocol filter used.

802.1Q tagging

All packets are untagged on the default VLAN 
(

default)

BOOTP

Enabled on the default VLAN (

default

)

Spanning Tree Protocol

Disabled; one defined as “s0” 

IP Routing

Disabled

Forwarding database aging 
period

30 minutes

RIP Protocol

Disabled

Autonegotiation

On

SW3800.BK  Page 10  Tuesday, May 5, 1998  5:20 PM

Содержание 3Com SuperStack 3 Switch 3800 Family























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды