manualshive.com logo in svg

3Com 3Com SuperStack 3 Switch 3800 Family, Руководство пользователя

Поделиться
Скачать
3Com 3Com SuperStack 3 Switch 3800 Family Скачать руководство пользователя страница 124

8-12

C

HAPTER

 8: IP U

NICAST

 R

OUTING

Displaying Router 
Settings

To display settings for various IP routing components, use the 
commands listed in Table 8-5.

Table 8-5   

Router Show Commands 

Command

Description

show ip config {vlan <name> | all}

Displays configuration information for one or more VLANs, 
including the following:

■

IP address, subnet mask

■

IP forwarding information

■

BOOTP configuration

■

VLAN name, VLANid

■

Global ICMP configuration

■

Global router advertisement configuration

show ip stats {vlan [<name> | all]}

Displays IP statistics for the CPU of the Switch.

show iparp {<ipaddress | vlan <name> 

| all | permanent}

Displays the IP Address Resolution Protocol (ARP) table. You 
can filter the display by IP address, VLAN, or permanent 
entries. Each entry displayed includes the following:

■

IP address

■

MAC address

■

Aging timer value

■

VLAN name, VLANid, and port number

■

Flags

show ipfdb {<ipaddress> <netmask> | 

vlan <name> | all}

Displays the contents of the IP forwarding database table. 
Used for technical support purposes.

show iproute vlan {<name> | all | 

permanent | <ipaddress> <netmask>}

Displays the contents of the IP routing table.

show rip {vlan <name> | all}

Displays RIP configuration and statistics for one or more 
VLANs. Display includes the state for RIP settings, and 
interface states. Statistics include the following:

■

Packets transmitted

■

Packets received

■

Bad packets received

■

Bad routes received

■

Number of RIP peers

■

Peer information

(continued)

SW3800.BK  Page 12  Tuesday, May 5, 1998  5:20 PM

Содержание 3Com SuperStack 3 Switch 3800 Family























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды