3Com 3CBLUG16A - Baseline Switch 2816 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 72

background image

50

C

HAPTER

5: T

ROUBLESHOOTING

■

The device being connected to is powered on and
operating correctly.

■

The cable is connected at both ends.

■

The cable is not damaged.

■

If the connection is to a workstation, that the
workstation's network interface is installed and
configured correctly.

■

The correct category of cable is being used for the
required link speed. Category 3 cables can be used
for 10BASE-T operation only. Category 5 cable is
required for 100BASE-TX or 1000BASE-T. 3Com
recommends Category 5e or 6 cables for
1000BASE-T operation.

A fiber cable is connected but the Module Present
LED does not light

Check that:

■

The Receive (RX) and Transmit (TX) cable connectors
are not swapped.

■

The fiber cable is in good condition.

■

The SFP module is correctly inserted.

■

A 3Com SFP module is being used. Refer to
“Approved SFP Transceivers” on page 18 for details.

■

The equipment at the far end is installed and
correctly configured.

The Link/Activity LED is lit but the network
performance of the Switch is poor

The Switch supports full-duplex auto-negotiation. If the
connected device does not support auto-negotiation,
ensure it is configured for half-duplex operation only. If
the connected device has auto-negotiation disabled or
over-ridden, and is configured as full duplex, the Switch
will configure the link as half duplex, causing a
mis-match that will reduce network performance when
data is transmitting and receiving simultaneously on the
same link.

Ensure that the connected device has either:

■

Auto-negotiation enabled, or

■

The ports are configured for half-duplex operation

All ports appear to show continual activity

There may be broadcast storms on the network.
Remove port connections one at a time, waiting a few
seconds between each port. If the LEDs go off after
removing a port connection, the device that was
connected to that port is introducing an excessive
amount of broadcast frames to the network (some
pieces of network equipment operate by sending out
broadcast frames regularly). Refer to the documentation
that accompanies the device for information on
disabling the broadcast operation.

The Firmware image has become corrupted

«
...
48
49
50
51
52
...
»

Содержание 3CBLUG16A - Baseline Switch 2816









































































Отзывы:

Нет отзывов

Похожие инструкции для 3CBLUG16A - Baseline Switch 2816

LightSpeed Appliance QLS250

Бренд: Quantum Страницы: 12

Бренд: D-Link Страницы: 83

Бренд: Profile Страницы: 6

Бренд: Intellinet Страницы: 2

Бренд: Lancom Страницы: 102

Бренд: NETGEAR Страницы: 2

Бренд: Perle Страницы: 2

Бренд: Juniper Страницы: 2

FieldPoint FP-3000

Бренд: National Instruments Страницы: 118

EdgeRouter PoE ERPoe-5

Бренд: Ubiquiti Страницы: 13

Бренд: H3C Страницы: 4

8-Port 10/100Mbps Fast Ethernet Switch

Бренд: Amer.com Страницы: 14

Бренд: NetComm Страницы: 65

Бренд: AMG Страницы: 4

GigaVUE H TA100-CXP

Бренд: Gigamon Страницы: 115

Бренд: Eaton Страницы: 32

Бренд: EINHELL Страницы: 32

Бренд: BinTec Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды