background image

Storage

Always set the marker on “Safe”, and remove the Feed Tube, all paintballs and the 
propellant source. Place the marker in a secure location where it cannot be accessed by
unauthorized persons.

Troubleshooting Guide

Symptom

Cause

Cure

Does not Fire

Not Cocked

Cock the Bolt to the Rear

On “Safe”

Push Safety to “Fire”

Out of Gas

Replace 12 Gram CO

2

Leaks air down Barrel

Bad Cup Seal

Replace/Reset Cupseal

Not Cocked

Cock the Bolt to the rear

Leaks air from Exhaust

Bad Valve Face O-Ring

Replace Valve Face O-Ring

Hole under 12 Gram plus

Does not Re-cock

Low on Gas

Replace 12 Gram CO

2

Bad Hammer or Hammer

Replace Hammer O-Ring or

O-Ring

Hammer

Needs Lubrication

Lubricate Hammer/Bolt

Debris Around Bolt/Hammer 

Remove the Bolt/Hammer and clean
parts and breach

Goes “Full Auto”

Sear not catching

Tighten Grip Frame Screws

Low on Gas

Replace 12 Gram CO

2

Propellant Source

Bad Hammer or Hammer

Replace Hammer O-Ring or

O-Ring

Hammer

Needs Lubrication

Lubricate Hammer and Bolt

Excessive Ball Breakage

Low Quality Paintballs

Use better Paintballs, such as

Diablo

brand

When in doubt, thoroughly clean and lubricate the marker. Many marker function 
problems are caused by excessive dirt or lack of lubrication.

For further assistance go to www.paintballsolutions.com or call 1.800.220.3222

Warranty Registration

To assist us in providing the best customer service possible and to increase your war-
ranty from 90 days to one year at no additional cost Complete and mail this to:

Paintball Solutions
570 Mantua Blvd.
Sewell, NJ  08080

Or register online at www.PaintballSolutions.com

Marker Type: PT Jr.

Name: ____________________________________________________

Address: __________________________________________________________

__________________________________________________________

City: _____________________ State:________    Zip: ______________

Country: ________________________________

Email Address: _____________________________________________

Serial Number (located on left side of marker):______________________

Date of Purchase: ___________________________________

Place of Purchase: _________________________________________________

P A I N T B A L L M A R K E R

8

9

 

Содержание PT Jr.







Отзывы: