2N IP Handset Скачать руководство пользователя

Страница: 48 / 68

Add dialing rules:

Picture 20 - Custom setting of dial - up rules

Table 9 - Dial - up rule configuration table

Parameters

Description

Dial rule

There are two types of matching: Full Matching

or Prefix Matching. In Full matching, the entire

phone number is entered and then mapped per

the Dial Peer rules.

In prefix matching, only part of the number is

entered followed by T. The mapping with then

take place whenever these digits are dialed.

Prefix mode supports a maximum of 30 digits.

Note: Two different special characters are used.

◼

x -- Matches any single digit that is dialed.

◼

[ ] -- Specifies a range of numbers to be matched. It may be a range, a list of ranges separated

by commas, or a list of digits.

Destination

Set Destination address. This is for IP direct.

Port

Set the Signal port, and the default is 5060 for

SIP.

Alias

Set the Alias. This is the text to be added,

replaced or deleted. It is an optional item.

Note: There are four types of aliases.

◼

all: xxx

–

xxx will replace the phone number.

Содержание IP Handset





































































Результаты поиска

Содержание IP Handset

Отзывы:

Похожие инструкции для IP Handset

Бренды по названию

Популярные бренды

2N IP Handset, Руководство пользователя

Результаты поиска

Содержание IP Handset

Отзывы:

Похожие инструкции для IP Handset

Бренды по названию

Популярные бренды